hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Information regarding recent vulnerabilities

    HP is aware of the recent class of vulnerabilities referred to as “speculative execution side-channel attacks”. HP has released a security bulletin for systems with Intel x86 processor, and will continue to provide more information on other processors (ARM, AMD) as it becomes available. 

hp-concentra-wrapper-portlet

Actions
Loading...

Removing the Stand in HP Omni 100-5000 Series Desktop PCs

This document applies to HP Omni 100-5000 series desktop computers.
HP Omni 100-5000 series desktop computer
  • Remove any media (CD, DVD, and memory cards) from the computer.
  • Turn off the computer and disconnect all cables. Be sure to disconnect the network cable before disconnecting the power cord.
  • Transfer the computer to a clean, flat, stable work surface over a noncarpeted floor. HP recommends that you put down a blanket, towel, or other soft cloth to protect the screen from scratches or other damage.
  • Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards and other components. Use an antistatic wrist strap and a conductive foam pad when working on the computer.
  • Do not remove a component from its protective packaging until you are ready to install it.
  caution:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
Video overview
View the following video before using the steps in this article.
  note:
For best quality on dial-up connections, wait until the video has fully loaded before viewing.
Removing the stand
Remove the stand to mount the computer on the wall. Use the following steps to remove the stand:
Step 1
To remove the stand, first remove the hinge cover above the stand.
For instructions to remove the hinge cover, see the HP support document, Removing and Replacing the Back Covers.
Prying off the hinge cover
Step 2
Lift the hinge cover off and away from the computer.
Removing the cover
Step 3
Remove the three screws that fasten the stand to the computer.
  note:
These screws for the stand special long screws. Keep them with the stand.
Removing the screws for the stand
Step 4
Slide the stand up.
Sliding the stand up
Step 5
Tilt the stand up and remove it from the computer.
Removing the stand from the computer
Replacing the stand
Use the following steps to replace the stand:
Step 1
Find the hooked tab at the top of the stand.
Finding the hooked tab at the top of the stand
Step 2
Find the slot for the stand inside the computer.
Finding the slot inside the computer
Step 3
To replace the stand, hook the tab into the slot...
Aligning the stand
... and tilt the stand down until the stand is secure.
Sliding the stand into place
Step 4
Replace the three screws that secure the stand to the computer. Use the same three screws that were removed previously.
Replacing the screws for the stand
Step 5
To replace the hinge cover, find the two small tabs on the hinge cover.
Finding the two tabs
Step 6
Find the two slots inside the computer.
Finding the two slots
Step 7
Align the tabs on the hinge cover with the slots on the back of the computer.
Replacing the cover
Step 8
Press down until the cover snaps into place.
Pressing down to snap the cover into place

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Flag South Africa

hp-detect-load-my-device-portlet

Actions
Loading...