hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Fix Windows 10 Update Issues

    Resolve Windows 10 or update issues on an HP computer or printer – Click here

hp-concentra-wrapper-portlet

Actions
Loading...

HP EliteBook 8530w Mobile Workstation - Removing and Replacing the Hard Disk Drive

Introduction

This document is provided to assist in removing and replacing the Hard disk drive for the HP EliteBook 8530w Mobile Workstation.

Minimum skill level

The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.

Tools required

P1 Phillips-head screwdriver

Parts required

note:
Part numbers are subject to change.
The replacement part number will vary depending on the Hard disk drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
320 GB Serial ATA (SATA) hard drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
501118-001 (Modified)
Yes
250 GB Serial ATA (SATA) hard drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
495059-001 (Modified)
Yes
250 GB Serial ATA (SATA) hard drive - 5,400 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
495058-001 (Modified)
Yes
160 GB Serial ATA (SATA) hard drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
495057-001 (Modified)
Yes
160 GB Serial ATA (SATA) hard drive - 5,400 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
495056-001 (Modified)
Yes
120 GB Serial ATA (SATA) hard drive - 5,400 RPM, 2.5-inch form factor, 9.5 mm height - Includes bracket
495055-001 (Modified)
Yes
SPS-DRV, SSD SATA 80G 2.5
501113-001 (Modified)
Yes
note:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Summary of instructions

To view a video demonstrating the procedure for removing the Hard disk drive, click on the link below. Or use the product video listing on the HP Services Media Library, then select Hard disk drive from the menu on the upper left hand side of the screen.
Click here to view the Hard disk drive removal video (Right-click on the video link above to open in a new window/tab).

Hard disk drive removal

  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      caution:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. Loosen the two captive P1 Phillips-head screws that secure the hard disk drive cover to the bottom of the notebook.
  3. Use your finger or a flat-bladed tool to lift the inside edge of the hard disk drive cover and remove it.
  4. Loosen the captive, spring-loaded P1 Phillips-head screw that secures the hard disk drive.
  5. Grasp the Mylar tab and pull the hard disk drive toward the outside of the base enclosure to disconnect the hard disk drive from the system board connector.
  6. Lift the hard disk drive out of the bay and remove.
  7. Place the hard disk drive in a static dissipative bag.

Hard disk drive replacement

  1. Remove the hard disk drive from the static dissipative bag.
  2. Place the hard disk drive into the hard disk drive bay.
  3. Push the hard disk drive toward the inside of the base enclosure until the connector is seated.
  4. Tighten the captive, spring-loaded P1 Phillips-head screw that secures the hard disk drive.
  5. Toe the hard disk drive cover into the enclosure.
  6. Tighten the two captive P1 Phillips-head screws.

Parts return


hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag South Africa

hp-detect-load-my-device-portlet

Actions
Loading...