hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP Enterprise M607-M609, M610-M612, HP LaserJet Managed E60055-E60075, E60155-E60175 - Removal and replacement: Tray roller kit

Learn how to remove and replace the tray 2 roller kit.

Mean time to repair: 15 minutes

Service level: Intermediate

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part number

Part description

J8J70-67904

Tray roller kit

Required tools

  • No special tools are needed to remove or install this assembly.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

No post service test is available for this assembly.

Remove the tray 2 separation and pickup rollers

Follow these steps to remove the tray 2 separation and pickup rollers.

  1. Open the paper tray for which the rollers will be replaced.

    CAUTION:

    Do not extend more than one paper tray at a time. Do not use the paper tray as a step. Keep hands out of the paper trays when closing. All trays must be closed when moving the printer.

    Open the paper tray to locate the rollers

    Open the paper tray to locate the rollers
  2. Rotate the printer.

    Rotate the printer

    Rotate the printer
  3. Tray 2 rollers only: On the back side of the printer, open the rear door.

    Open the rear door

    Open the rear door
  4. Tray 2 rollers only: Raise the transfer assembly.

    Raise the transfer assembly

    Raise the transfer assembly
  5. Tray 2 rollers only: Do the following:

    • Lower the access cover.

    • Go to step h.

    Lower the access cover

    Lower the access cover
  6. Tray 3 rollers only: On the back side of the printer, open the rear lower cover.

    Open the rear lower cover

    Open the rear lower cover
  7. Tray 3 rollers only: Do the following:

    • Lower the access cover.

    • Go to step h.

    Lower the access cover

    Lower the access cover
  8. Remove the orange separation roller tool from the packaging.

    Remove the orange separation roller tool

    Remove the orange separation roller tool
  9. Locate the separation roller.

    Locate the separation roller

    Locate the separation roller
  10. Install the orange tool in the separation roller until it snaps into place.

    Install the orange tool in the separation roller

    Install the orange tool in the separation roller
  11. Slide the roller to the left.

    Slide the roller to the left

    Slide the roller to the left
  12. Tilt the end of the tool down (callout 1), and then pull straight out of the printer (callout 2) to remove the separation roller.

    Tilt the tool down, and then remove the separation roller

    Tilt the tool down, and then remove the separation roller
  13. Remove the orange tool from the separation roller.

    Note:

    The tool will be used to install the new separation roller.

    Remove the orange tool from the separation roller

    Remove the orange tool from the separation roller
  14. Locate the pickup and feed rollers.

    Locate the pickup and feed rollers

    Locate the pickup and feed rollers
  15. Locate and pull down the blue tab to unlock the pickup and feed rollers.

    Pull down the blue tab to unlock the pickup and feed rollers

    Pull down the blue tab to unlock the pickup and feed rollers
  16. Use the blue tab as a handle to slide the rollers to the left to compress the left blue post until it clicks into place.

    Slide the blue tab left, compressing the left blue post until it clicks

    Slide the blue tab left, compressing the left blue post until it clicks
  17. Slightly move the rollers to the right to free them from the blue post. Make sure that the roller is clear of the black post on the right.

    Slightly move the rollers to the right to free them from the blue post

    Slightly move the rollers to the right to free them from the blue post
  18. Slightly lift up the front of the roller assembly (callout 1), and then pull the assembly away from the printer (callout 2) to remove it.

    Lift up the front of the roller assembly and pull away to remove it

    Lift up the front of the roller assembly and pull away to remove it
  19. If the left post does not stay in the locked position, press the end of the post left until it clicks into place.

    Securely lock the left post into position by pressing the end left until it clicks

    Securely lock the left post into position by pressing the end left until it clicks

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the tray 2 separation and pickup rollers

Follow these steps to install the tray 2 separation and pickup rollers.

  1. Align the arrow on the roller assembly with the arrow in the printer, and then slide the rollers into the printer.

    Align the roller assembly and slide the rollers into the printer

    Align the roller assembly and slide the rollers into the printer
  2. Slide the rollers to the right onto the black shaft.

    Slide the rollers to the right onto the black shaft

    Slide the rollers to the right onto the black shaft
  3. Confirm correct installation: The white hook on the top of the roller assembly (callout 1) will hook onto a sheet metal plate (callout 2) when installed correctly.

    Correctly install the white hook onto a sheet metal plate

    Correctly install the white hook onto a sheet metal plate
  4. Locate the lever on the blue shaft on the left, and then release the lever by pressing upward.

    Note:

    The blue shaft should spring to the right to click into position to hold the rollers in place.

    Release the lever by pressing upward

    Release the lever by pressing upward
  5. Remove the orange tool from the roller assembly by pulling it away from the printer.

    Remove the orange tool

    Remove the orange tool
  6. IMPORTANT: Pivot the tab up and snap it into place against the rollers to correctly lock the rollers in place.

    Note:

    The blue arrow on the printer is hidden when the cover is correctly snapped into place.

    Pivot the tab up and snap it to lock the rollers correctly in place

    Pivot the tab up and snap it to lock the rollers correctly in place
  7. Incorrect installation: If the rollers are hanging, or at an angle, they are not installed correctly.

    Rollers hanging at an angle are not installed correctly

    Rollers hanging at an angle are not installed correctly
  8. Correct installation: Make sure that the hook on the top of the rollers is attached to the metal chassis plate inside the printer. If the rollers are not installed correctly, go back to step 2 and reinstall the assembly.

    Correctly attach the rollers top hook to the metal chassis plate inside the printer

    Correctly attach the rollers top hook to the metal chassis plate inside the printer
  9. Install the orange separation roller tool onto the replacement separation roller.

    Note:

    The tool will snap into place when it is fully installed.

    Install the replacement separation roller onto the orange tool

    Install the replacement separation roller onto the orange tool
  10. Tilt the orange tool slightly away from the printer, and then install the roller into the printer so that the opening in the roller (callout 1) fits over the white tab (callout 2) on the printer rail.

    Slightly tilt the roller tool

    Slightly tilt the roller tool
  11. When installed correctly, the embossed arrow on the roller case aligns with the white tab on the rail.

    Install the roller over the white tab with the arrow aligned

    Install the roller over the white tab with the arrow aligned
  12. Do the following:

    • Align the center of the roller with the end of the metal shaft.

    • Slide the roller to the right onto the metal shaft until it snaps into place.

    Align the roller and slide it onto the metal shaft until it snaps into place

    Align the roller and slide it onto the metal shaft until it snaps into place
  13. Remove the orange tool by pulling it away from the printer.

    Remove the orange tool

    Remove the orange tool
  14. Tray 3 rollers only: Raise the access cover.

    Raise the access cover

    Raise the access cover
  15. Tray 3 rollers only: On the back side of the printer, close the rear lower cover.

    Close the rear lower cover

    Close the rear lower cover
  16. Tray 2 rollers only: Close the access cover.

    Close the access cover

    Close the access cover
  17. Tray 2 rollers only: On the back side of the printer, close the rear door.

    Close the door

    Close the door
  18. Close the paper tray for which the rollers were replaced.

    Close the paper tray

    Close the paper tray

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Vietnam

hp-detect-load-my-device-portlet

Actions
Loading...