HP Customer Support - Knowledge Base




  • Information
    Learn how to upgrade to Windows 11

    Windows 11 Upgrade Guide

  • Feedback



HP 1859m, 2009f/m/v, 2159m/v, 2309m/v, 2509m, and 2709m Flat Panel Monitors - Using and Adjusting your Monitor

This document describes using and adjusting HP 1859m, 2009f/m/v, 2159m/v, 2309m/v, 2509m, and 2709m flat panel monitors

Installing drivers

Install the monitor-driver INF and ICM files from the CD, or download them from the Internet as follows:

Installing drivers from the CD

To install the monitor driver from the CD:
  1. Insert the CD in the computer CD drive.
    The CD menu displays.
  2. Select the language.
  3. Click Install Monitor Driver Software.
  4. Follow the on-screen instructions.
  5. Restart the computer.
  6. Check that the proper resolutions and refresh rates display in the Display Properties window in Control Panel.

Installing drivers from the Web

To download the latest version of drivers and software files from the HP Support Web site:
  1. Select the country/region.
  2. Select Download Drivers and Software.
  3. Type the model number of the monitor, for example 2159m.
    The software download pages for the monitor display.
  4. Make sure the system meets the specified requirements.
  5. Download and install the driver and software files by following the steps on the screen.

Front panel components

Monitor control buttons are located under the lower right front panel of the monitor.
Figure : Monitor control buttons
Image of the monitor control buttons.
Turns the monitor on and off, and indicates standby or sleep mode.
Opens, selects, or exits the OSD menu.
Adjusts the volume level.
Navigates backward through the OSD menu and decreases adjustment levels.
Chooses video input source from the computer.
Navigates forward through the OSD menu and increases adjustment levels.
Auto-adjusts the display to the ideal setting. Always start with this when adjusting monitor settings.
Enters the selected option.


Optimize the screen performance for the VGA input by using the Auto/Select button on the monitor and the auto-adjustment pattern software on the CD provided. This software can correct the following conditions:
  • Fuzzy or unclear focus
  • Ghosting, streaking, or shadowing effects
  • Faint vertical bars
  • Thin, horizontal scrolling lines
  • Off-center picture
To use the auto-adjustment feature:
  1. Allow the monitor to warm up for 20 minutes before adjusting.
  2. Press the Auto/Select button on the monitor front panel.
  3. Press the Menu button on the monitor panel, and then select Image Control, followed by Auto Adjustment from the OSD menu.
    If the result is not satisfactory, continue with this procedure.
  4. Insert the CD in the computer CD drive.
    The CD menu displays.
  5. Select the language.
  6. Select Open Auto-Adjustment Software.
    The setup test pattern displays.
    Figure : Setup test pattern
    Image of the setup test pattern.
  7. Press the Auto/Select button on the monitor panel to produce a stable, centered image.

Using Onscreen Display (OSD)

Follow these steps to adjust monitor settings with the on-screen display menu.
  1. Turn on the computer and monitor.
  2. Press the Menu button to access the on-screen display menu.
    The OSD main menu opens.
    Figure : OSD Main Menu
    Image of the OSD menu.
  3. To navigate through the Main or Submenu menus, on the monitor front panel press the + (plus) button to move up, or the (minus) button to move in reverse.
  4. Press the Select button to select the highlighted item.
  5. When a menu item is selected and its corresponding screen displays, use the + or button to adjust the scale of the item.
  6. Select Save and Return to save the adjustment, or Cancel or Exit if you do not want to save the adjustment.
  7. Press the Menu button to exit the on-screen display menu.
    When a menu is displayed, if the buttons remain untouched for 30 seconds, adjustments and settings are saved and the menu closes automatically.
The following table lists the OSD functions:
  • Press Cancel to return to the previous menu level.
  • Press Save and Return to save all changes and return to the OSD Main Menu screen. (This option is active only if you actually make a change.)
  • Press Reset to change back to the previous setting.
Main Menu Options
Submenu Options
Switch Video Input
Switches the video input signal source when the monitor is connected to two active and valid video sources.
Adjusts the brightness level of the screen.
Adjusts the contrast level on-screen between darks and lights.
Image Control
Auto Adjustment
Automatically adjusts the screen image (use only with the VGA input).
Horizontal Position
Adjusts the horizontal position of the picture (VGA input only).
Vertical Position
Adjusts the vertical position of the picture (VGA input only).
Minimizes any vertical bars or strips visible on the screen background. Adjusting the clock also changes the horizontal screen image (VGA input only).
Clock Phase
Adjusts focus. This adjustment helps remove horizontal noise, and clear or sharpen characters or images (VGA input only).
Custom Scaling
Selects how displayed information on the monitor is formatted. Select:
  • Fill to Screen - Image fills the entire screen and might look distorted or elongated because of non-proportional scaling of height and width.
  • Fill to Aspect Ratio - Image is sized to fit the screen and maintains proportional image.
Selects the screen color. The factory default is 6500 K or Custom Color, depending on the model.
9300 K
Changes to slightly bluish white
6500 K
Changes to slightly reddish white
Custom Color
Selects and adjusts your own color scales:
  • R - Sets your own red color levels.
  • G - Sets your own green color levels.
  • B - Sets your own blue color levels.
Sets your screen colors to adapt to the color standards used in the image technology industry.
Quick View
Selects movie mode.
Selects photo mode.
Selects gaming mode.
Selects text mode.
Settings saved when user adjusts the brightness, contrast, or color in one of the Quick View options.
Selects the language in which the OSD menu is displayed. English, French, German, Italian, Dutch, Spanish, Japanese, and Simplified Chinese languages are supported. The factory default is English.
Adjusts the volume level.
OSD Control
Adjusts the position of the OSD menu on the screen.
  • Horizontal OSD Position - Changes the viewing position of the OSD menu to the left or right. The factory default range is 50.
  • Vertical OSD Position - Changes the viewing position of the OSD menu to the top or bottom of the screen. Default range is 50.
  • OSD Transparency - Makes it possible to view background information through the OSD.
  • OSD Timeout - Sets the time in seconds the OSD is visible after the last button is pressed. Factory default is 30 seconds.
Power Saver
Enables the power saving feature. Select On or Off. Factory default is On.
Mode Display
Displays the resolution, refresh rate, and frequency information on the screen each time the OSD Main Menu is accessed. Select On or Off.
Power-On Status Display
Displays the operating status of the monitor each time the monitor is turned on. Select the place where the status is displayed: Top, Middle, Bottom, or Off.
DDC/CI Support
Allows the computer to control some OSD menu features such as brightness, contrast, and color temperature.
Bezel Power LED
Turns the light (LED) in the power button on or off. When set to off, the light always stays off.
Sleep Timer
Provides the timer-adjustment menu options:
  • Set Current Time - Sets the current time in hours and minutes.
  • Set Sleep Time - Sets the time of no activity when the monitor will go into sleep mode.
  • Set on Time - Sets the time the monitor should wake up from sleep mode.
  • Timer - Sets the Sleep Timer feature on or off.
  • Sleep Now - Immediately sets the monitor to enter sleep mode.
Default Video Input
Selects the default video input signal when the monitor is connected to two active and valid video sources. The default is DVI. You must restart the computer to have the change take effect.
Current Settings
Shows the current input video mode.
Recommended Settings
Shows recommended resolution and refresh rate.
Serial Number
Shows the monitor's serial number (for if you have to contact HP Support).
Shows the firmware version of the monitor.
Backlight Hours
Shows the total hours of backlight operation.
Service Support
For service support, see HP Support
Factory Reset
Returns settings to factory defaults.

Locking OSD settings

When the OSD is locked, settings cannot be changed in the OSD menu.
The OSD functionality is enabled or disabled by pressing the Menu button and holding it for 10 seconds. When disabling the OSD, an OSD Lock-out message is displayed for 10 seconds. When the OSD is locked and an OSD menu button is pressed, the OSD Lock-out message is displayed for an additional 10 seconds. When the OSD is locked, pressing the OSD menu button for 10 seconds unlocks the OSD and displays the main menu.

Identifying monitor conditions

Special messages display on the monitor for the following monitor conditions:
  • Input Signal Out of Range: Indicates the monitor does not support the input signal because the resolution or refresh rate are set higher than the monitor supports. Recommended refresh rates are as follows:
    • For the 1859m monitor: 1366 x 768 @ 60 Hz.
    • For the 2009f, 2009m, and 2009v monitor: 1600 x 900 @ 60 Hz .
    • For the 2159m and 2159v monitor: 1920 x 1080 @ 60 Hz.
    • For the 2309m and 2309v monitor: 1920 x 1080 @ 60 Hz.
    • For the 2509m monitor: 1920 x 1080 @ 60 Hz.
    • For the 2709m monitor: 1920 x 1080 @ 60 Hz.
  • Monitor Going to Sleep: Indicates the screen display is entering sleep mode.
  • Check Video Cable: Indicates a video input cable is not correctly connected to the computer or monitor.
  • OSD Lock-out: When the OSD is locked, the warning message OSD Lock displays for 10 seconds.
  • No Input Signal: Indicates the monitor is not receiving a video signal from the computer on the monitor video input connector. Check whether the computer or input signal source is off or in the power-save mode.
  • Auto Adjustment in Progress: Indicates the auto-adjustment function is active and in process.


The following table lists possible problems, the possible cause of each problem, and the recommended solutions.
Power LED is not on.
Make sure the power cord is connected to a grounded power outlet and to the monitor.
No Plug and Play.
For the Plug and Play feature of the monitor to work, you need a Plug and Play compatible computer and video card. Check with your computer manufacturer.
Check the monitor video cable and make sure none of the pins are bent.
Make sure the HP monitor drivers are installed.
Picture is fuzzy and has ghosting and shadowing problems.
Adjust the contrast and brightness controls.
Make sure you are not using an extension cable or switch box. HP recommends plugging the monitor directly into the video card output connector on the back of the computer.
For VGA input, use the auto-adjustment feature to try to fix this problem.
Picture bounces and flickers, or a wave pattern is present in the picture.
Move electrical devices that might cause electrical interference as far away from the monitor as possible.
Use the maximum refresh rate the monitor is capable of at the resolution you are using.
Monitor is stuck in “Active Off-Mode.”
Check the computer:
  • The computer power switch should be in the On position.
  • The computer video card should be snugly seated in its slot.
  • Make sure the computer is operational by pressing the Caps Lock key on the keyboard while observing the Caps Lock LED. The LED should turn on and off.
Make sure the monitor video cable is correctly connected to the computer.
Inspect the monitor video cable and make sure none of the pins are bent.
“Out of Range. Set Monitor to [your monitor's optimum resolution]” is displayed on the screen.
Restart the computer and enter Safe Mode. Change the settings to the recommended resolution. Restart the computer so that the new settings take effect.
Missing one of the primary colors (red, green, or blue).
Make sure the monitor video cable is correctly connected to the computer.
Inspect the monitor video cable and make sure none of the pins are bent.
Screen image is not centered or sized correctly.
Adjust horizontal and vertical screen position.
For VGA input, use the auto-adjustment feature to try to fix this problem.
Picture has color defects (white does not look white).
Adjust RGB color or select color temperature.
Unable to set the monitor to the optimal resolution.
Make sure that the graphics adapter supports the optimum resolution (1920 x 1080).
Make sure the HP monitor drivers are installed.

Power-saver feature

When the monitor is in normal operating mode, the Power light is green.
The monitor supports a reduced power state which occurs if the monitor detects the absence of either the horizontal sync signal or the vertical sync signal. When detecting the absence of these signals, the screen becomes blank, the backlight turns off, and the Power light turns orange.

Tips and recommendations

  • Unplug your monitor from the wall outlet before cleaning. Clean the monitor plastics with a clean cloth dampened with water. Do not use liquid cleaners or aerosol cleaners. Clean the monitor screen with an antistatic screen cleaner.
  • Do not open your monitor cabinet or try to service this product yourself. Adjust only those controls that are covered in the operating instructions. If your monitor is not operating correctly, or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider.
  • Use only a power source and connection appropriate for this monitor, as indicated on the label or back plate of the monitor.
  • Never disconnect the monitor by pulling the cord.
  • Turn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by using a screen saver program and turning off the monitor when not in use.
  • When removing the monitor base, place the monitor face down on a soft flat area to prevent it from getting scratched, defaced, or broken.
  • Burn-in image damage might occur on monitors that display the same static image on the screen for a prolonged time. To avoid burn-in image damage on your monitor, always start a screen saver or turn off the monitor when it is not in use for a prolonged period.






Country/Region: Flag United States