hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

hp-concentra-wrapper-portlet

Actions
Loading...

HP t610 Series Flexible Thin Clients - Hardware changes

General hardware installation sequence

To ensure the proper installation thin client hardware components:
  1. Back up any data, if necessary.
  2. If the thin client is powered on:
    1. Turn the unit and any other attached devices off.
    2. Disconnect the power cord from the wall outlet.
    3. Disconnect any external devices or cables, such as a cable lock.
      warning:
    To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect the power cord from the wall outlet and allow the internal system components to cool before touching.
      warning:
    To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the network interface controller (NIC) receptacles.
      caution:
    Static electricity can damage the electronic components of the thin client or optional equipment. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object. See Electrostatic dischargeElectrostatic discharge for more information.
  3. Remove the stand, if it is installed. See Removing the standRemoving the stand for more information.
  4. Remove the side access panel and metal side cover, if necessary. See Removing and replacing the side access panel and metal side cover for more information.
  5. Remove any hardware that you will replace.
  6. Install or replace equipment. For removal and replacement procedures, see the following sections:
    note:
    Option kits include more detailed installation instructions.
  7. Replace the side access panel and metal side cover. See Removing and replacing the side access panel and metal side cover for more information.
  8. Install the stand, if you will be using the thin client unmounted in a vertical orientation. See Installing the standInstalling the stand for more information.
  9. Reconnect any external devices and power cords.
  10. Turn on the monitor, the thin client, and any devices you want to test.
  11. Load any necessary drivers.
    note:
    You can download select hardware drivers from HP at http://www.hp.com/country/us/eng/support.html.
  12. Reconfigure the thin client, if necessary.

Removing and replacing the side access panel and metal side cover

Removing the side access panel

  warning:
Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.
To remove the left or right access panel:
  1. Remove the stand, if it is installed. See Removing the standRemoving the stand for more information.
  2. Press the tab on the bottom cover (1), and then slide the cover back (2) and lift it off the chassis.
    Figure :
  3. Lay the thin client on its side on a secure working surface.
    • Remove the right side access panel to remove or install a SODIMM.
    • Remove the left side access panel to:
      • Remove or replace the battery
      • Install or remove a flash memory module
      • Install or remove an internal hard drive
      • Install or remove a PCI Express card
  4. Slide the access panel about 6.35 mm (1/4 inch) toward the bottom of the unit, and then lift the access panel up and off the chassis.
    Figure :

Removing the left metal side cover

note:
Do not remove the metal side cover to install a SODIMM. The SODIMM compartment is in the right side of the chassis.
You must remove the metal side cover to access internal components such as the battery or to install a flash memory module, internal hard drive, or PCI-Express card.
  1. Push the tab in the front edge of the side cover toward the back to release the sided cover (1).
  2. Lift the front edge of the metal side cover (2), then pull the cover to the front and lift it off the chassis (3).
    Figure :

Replacing the left metal side cover

  1. Place the metal side cover on the chassis, rear edge first, making sure to insert the two tabs of the rear edge into the notches in the chassis (1).
  2. Align the tabs on both sides of the cover and press the front edge down firmly until the latch closes.
    Figure :

Replacing the side access panel

To replace the access panel:
  1. Place the access panel on the side of the unit, offset about 6.35 mm (1/4 inch) toward the top of the unit (1), allowing the hooks on the underside of the panel to slip into notches in the side access panel.
  2. Slide the panel toward the bottom of the unit until it locks into place (2).
    Figure :
  3. Turn the chassis upside down. Align the hooks on the underside of the bottom cover with the slots in the chassis and press the cover down and then forward until it locks in place.
    Figure :
  4. Replace the stand, if the thin client is to be used in the tower orientation.

Removing and replacing the battery

Before beginning the replacement process, review General hardware installation sequence for procedures you should follow before and after installing or replacing hardware.
  warning:
You must remove the left side panel to access the battery. Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.
To remove and replace the battery:
  1. Locate the battery on the system board.
  2. To remove the battery, pull the metal clamp extending above the battery aside and lift the battery out (1).
    Figure :
  3. To insert the replacement battery, position it with the positive side facing the chassis wall. Slide the battery down into the slot until the clamp snaps over the edge of the battery (2).
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to www.hp.com/recycle.
Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP partner, or their agents.
The Taiwan EPA requires dry battery manufacturing or importing firms, in accordance with Article 15 or the Waste Disposal Act, to indicate the recovery marks on the batteries used in sales, giveaways, or promotions. Contact a qualified Taiwanese recycler for proper battery disposal.

Installing thin client options

Installing a SODIMM

The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) small outline dual inline memory modules (SODIMMs).
The memory sockets on the system board can be populated with up to two industry-standard SODIMMs. These memory sockets are populated with at least one preinstalled SODIMM. To achieve the maximum memory support, you can populate the system board with up to 4 GB of memory.
For proper system operation, the SODIMMs must be:
  • industry-standard 204-pin
  • unbuffered non-ECC PC3-12800 DDR3-1600 MHz-compliant
  • 1.5 volt DDR3-SDRAM SODIMMs
The DDR3-SDRAM SODIMMs must also:
  • support CAS latency 9 DDR3 1600 MHz (9-9-9 timing)
  • contain the mandatory Joint Electronic Device Engineering Council (JEDEC) specification
In addition, the computer supports:
  • 2-Gbit non-ECC memory technologies
  • single-sided and double-sided SODIMMS
  • SODIMMs constructed with x8 and x16 devices; SODIMMs constructed with x4 SDRAM are not supported
note:
The system will not operate properly if you install unsupported SODIMMs.
Before beginning the replacement process, review General hardware installation sequence for procedures you should follow before and after installing or replacing hardware.
  warning:
You must remove the right side panel to access the SODIMM compartment. Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.
  caution:
You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board.
The memory module sockets have gold-plated metal contacts. When upgrading the memory, it is important to use memory modules with gold-plated metal contacts to prevent corrosion and/or oxidation resulting from having incompatible metals in contact with each other.
Static electricity can damage the electronic components of the computer or optional cards. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object.
When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module.
To install the SODIMM:
note:
Populate the SODIMM sockets in the following order: SODIMM1, then SODIMM2.
  1. Slide the serial number tab out of the way.
    note:
    Be sure not to lose this tab.
  2. Pull the front of the access plate up, and lift it off the thin client.
    Figure :
  3. Align the notched edge of the SODIMM with the tab in the socket.
      caution:
    To prevent damage to the SODIMM, hold it by the edges only. Do not touch the components on the SODIMM, and do not bend the SODIMM.
  4. Hold the SODIMM at approximately a 20-degree angle, and then press the SODIMM into the socket (1) until it is seated. Gently apply pressure to both the left and right edges of the SODIMM until the retention clips snap into place.
    note:
    A SODIMM can be installed in only one way. Match the notch on the SODIMM with the tab on the socket.
    Figure :
  5. Press the SODIMM down into the compartment (2).
  6. If you are installing the SODIMM in the HP t610 Thin Client, place a thermal pad on the SODIMM.
      caution:
    The thermal pad is required to help cool the SODIMM in the HP t610 Thin Client. (The HP t610 PLUS Thin Client does not require a thermal pad.)
    Figure :
  7. Insert the tab on the front edge of the access plate into its slot (1) and press the plate down lightly to engage the latch (2).
    Figure :
  8. Slide the serial number tab back to its original position.

Installing a flash memory module

Before beginning the installation process, review General hardware installation sequence for procedures you should follow before and after installing or replacing hardware.
  warning:
You must remove the left side panel to access the system board. Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.
  caution:
Static electricity can damage the electronic components of the computer or optional cards. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object. When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module.
To install the flash memory module:
  1. If an internal hard drive is installed, remove it. See Removing an internal hard drive for instructions.
  2. Locate the correct flash memory module socket on the system board.
    1. The PATA socket (1) is populated by default.
    2. The SATA socket (2) can be populated with an optional SATA flash memory module.
    Figure :
  3. Align the connector on the flash memory module with the socket on the system board and press the flash memory module into the socket.
    note:
    A flash memory module can be installed in only one way. Line up the hole in the flash memory module with the retention post on the system board.
    Figure :
  4. Press the module connectors firmly into the flash memory module socket (1), making sure that the retention post on the system board is aligned with the hole in the module.
    Figure :
  5. Insert the screw provided in the flash memory module option kit through the hole in the module into the retention post (2) and tighten to secure the module.

Replacing an internal hard drive

Before beginning the replacement process, review General hardware installation sequence for procedures you should follow before and after installing or replacing hardware.
  warning:
You must remove the left side panel to access the system board. Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.

Removing an internal hard drive

To remove an internal hard drive:
  1. If a PCI-Express card is installed, remove it.
  2. Lift the drive bracket latch (1) and slide the drive bracket out of the retention bracket (2).
    Figure :
  3. Remove the four screws that secure the hard drive in the drive bracket (1) and remove the hard drive from the bracket (2).
    Figure :
    note:
    Keep the four screws to use to install another hard drive.

Installing an internal hard drive

To install an internal hard drive:
  1. If a PCIe card is installed, remove it.
  2. Insert the hard drive into the drive bracket (1) and secure it by fastening the four screws provided in the kit (2).
    Figure :
  3. Locate the internal hard drive connector (1) and retention bracket (2) on the system board.
    Figure :
  4. Align the screws on the side of the drive bracket with the slots inside the retention bracket and slide the drive bracket into the retention bracket (1).
    Figure :
  5. Press the drive bracket latch down firmly to push the drive onto the internal hard drive connector and secure the drive assembly (2).
  6. Reinstall the PCIe card, if necessary. See Installing a PCI-Express card for instructions.

Installing a PCI-Express card

You may install an optional PCI-Express (PCIe) card in the HP t610 PLUS Thin Client, which has a PCIe riser card installed.
Before beginning the replacement process, review General hardware installation sequence for procedures you should follow before and after installing or replacing hardware.
  warning:
You must remove the left side panel to access the system board. Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet.
To install a PCIe card:
  1. Press down on the plastic blank tab and pull it out of the chassis.
    Figure :
  2. Open the metal latch securing the expansion slot cover on the inside of the thin client (1) and remove the expansion slot cover (2).
    Figure :
      caution:
    Do not lose this expansion slot cover. If you remove an expansion card, you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation.
  3. Align the PCIe card connector with the PCI riser card socket and the expansion slot. Press the PCIe card firmly into the socket to ensure that the PCIe card is seated correctly and that the connector fits the expansion slot properly (1).
    Figure :
  4. Close the metal latch to secure the PCIe card (2).

Installing external drives

Various external USB drives are available as options for the t610 Series Thin Clients. For more information about these drives, visit http://h10010.www1.hp.com/wwpc/us/en/sm/WF12a/12454-12454-321959.html, or refer to the instructions that accompany the option.
For more information about available options, visit the HP website at http://h10010.www1.hp.com/wwpc/us/en/sm/WF12a/12454-12454-321959.html.

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag United States

hp-detect-load-my-device-portlet

Actions
Loading...