hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Learn how to upgrade to Windows 11

    Windows 11 Upgrade Guide

  • Feedback

hp-concentra-wrapper-portlet

Actions
Loading...

Removing and Replacing the Display Panel Assembly for HP Pavilion x360 Notebook PCs

This document applies to HP Pavilion x360 notebook computers.
HP Pavilion x360 notebook computer

Before you begin

  • You need a Phillips head screwdriver.
  • Turn off the computer. Disconnect the Ethernet or modem cable. Disconnect the power cord.
  • Transfer the computer to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.
  • After removing static sensitive components, place them in static dissipative bags. Do not remove a component from its protective packaging until you are ready to install it.
  warning:
The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
  warning:
Before starting, power off the computer and wait for components to cool before starting these procedures.
  caution:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
  caution:
Procedures in this document are provided by HP for qualified service agents and as a courtesy to its customers. Servicing internal components increases the risk of damaging the computer which might not be covered under warranty. Understand the risk and refer to the product's warranty before attempting to service the computer.

Video overview

View the following video before using the steps in this article.
note:
The video and graphics in this article depict a specific configuration of notebook computer. These same removal and replacement procedures apply to all configurations for all HP Pavilion x360 Notebook computers.

Removing the display panel assembly

  warning:
Make sure the computer is disconnected from power before starting.
Follow the steps in this section to remove the display panel assembly.
Step 1
Remove the base enclosure.
For instructions to remove the base enclosure, see the HP support document, Removing and Replacing the Base Enclosure.
Removing the base enclosure
Step 2
Remove the wireless module.
For instructions to remove the wireless module, see the HP support document, Removing and Replacing Wireless Module.
Removing the wireless module
Step 3
Remove the wireless WWAN module.
For instructions to remove the wireless WWAN module, see the HP support document, Removing and Replacing the Wireless WWAN Module.
Removing the WWAN module
Step 4
Remove the wireless antenna cable from the routing channel on the top cover.
note:
It is important to notice the routing of the wireless antenna, the touch screen, and the display panel cables for future replacement.
Removing the wireless antenna cable from its routing channel
Step 5
Remove the two screws that secure the right display panel hinge to the top cover.
The two screws that secure the right hinge to the top cover
Step 6
Carefully open the right display panel hinge.
Opening the right display panel hinge
Step 7
Peel back the retention tape...
Peeling the tape from the connector on the system board
...and disconnect the touch screen cable from the connector on the system board.
Disconnecting the touch screen cable
Step 8
Remove the tape that secures the display panel cable to the computer.
Removing the tape securing the  display panel cable
Step 9
Disconnect the display panel cable from its connector on the system board.
Disconnecting the display panel cable
Step 10
Remove the foam pad from the Kensington lock bracket.
Removing the foam pad from the Kensington lock bracket
Step 11
Remove the three screws that secure the left display panel hinge to the top cover.
Removing the three screws that secure the left display panel hinge to the
Step 12
Carefully open the left display panel hinge.
Opening the left hinge
Step 13
Lift the top cover and carefully guide it out from under the display panel hinges.
  caution:
Take care not to scratch the display panel or top cover.
Lifting and removing the top cover

Replacing the display panel assembly

Use the steps in this section to replace the display panel assembly.
Step 1
Carefully guide the display under the display panel hinges and lower it into position.
  caution:
Take care not to scratch the display panel or top cover.
Guiding the display under the hinges
Step 2
Close the left display panel hinge.
Closing the left hinge
Step 3
Replace the three screws that secure the hinge to the top cover.
Replacing the three screws to secure the hinge to the top cover.
Step 4
Replace the foam pad on the Kensington lock bracket.
Replacing the foam pad
Step 5
Connect the touch screen cable into its connector on the system board...
Touch screen cable connector
...and replace the retention tape.
Replacing the retention tape
Step 6
Route the touch screen cable through the routing channel on the top cover,
Routing the touch screen cable in its channel
Step 7
Connect the display panel cable onto its connector on the system board.
Connecting the display panel cable
Step 8
Replace the tape that secures the display panel cable to the computer.
Retaping the display panel cable to the computer
Step 9
Close the right display panel hinge.
Closing the right hinge
Step 10
Replace the two screws that secure the right display panel hinge to the top cover.
Replacing the two screws to secure the hinge
Step 11
Route the wireless antenna cable through the routing channel on the top cover.
Routing the wireless cable antenna
Step 12
Replace the wireless WWAN module.
For instructions to replace the wireless WWAN module, see the HP support document, Removing and Replacing the Wireless WWAN Module.
Replacing the wireless WWAN module
Step 13
Replace the wireless module.
For instructions to replace the wireless module, see the HP support document, Removing and Replacing the Wireless Module.
Wireless module
Step 14
Replace the base enclosure.
For instructions to replace the base enclosure, see the HP support document, Removing and Replacing the Base Enclosure.
Replacing the base enclosure

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag United States

hp-detect-load-my-device-portlet

Actions
Loading...