Error:

Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions.

hp-support-head-portlet

Actions

HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions

hp-share-print-widget-portlet

Actions

Information

Coronavirus (COVID-19) Impact
We are experiencing longer than expected wait times to reach an agent. Please use our digital solutions like the Virtual Agent and Diagnostic Tools or your HP account for faster service. Instant Ink customers please visit instantink.com

hp-concentra-wrapper-portlet

Actions

HP and Compaq Desktop PCs - Motherboard Specifications, P5LP-LE (Leonite)

Figure : The P5LP-LE (Leonite) motherboard

Motherboard description

Manufacturer's motherboard name: ASUS P5LP-LE
HP/Compaq name: Leonite-GL8E

Form Factor

Micro-ATX: 24.4 cm (9.6 inches) x 24.4 cm (9.6 inches)

Chipset

Northbridge: Intel 945G
Southbridge: ICH7DH

Front-side bus speed

533 MHz, 800 MHz, 1066 MHz (processor dependent)

Processor upgrade information

Socket type: 775

Motherboard supports the following processor upgrades:

Core 2 Duo E6x00
Core 2 Duo E4x00
Pentium D 9x0 Dual Core
Pentium D 8xx Dual Core
Pentium 4 6x1 series
Celeron D 3xx series

Memory upgrade information

Dual channel memory architecture
Four 240-pin DDR2 DIMM sockets
Supports PC2 3200 (400 MHz), PC 4200 (533 MHz) and PC2 5300 (667 MHz) DDR2 DIMMs
non-ECC memory only, unbuffered
Maximum HP/Compaq approved memory is 4 GB*
- 32 bit PCs cannot address a full 4.0 GB of memory.

Video

Integrated graphics using Intel GMA 950

*Integrated video is not available if a graphics card is installed.

Integrated graphics using Intel GMA 950
Also supports PCI Express x16 graphics cards

Audio

Integrated Realtek ALC888 Audio

*Integrated audio is not available if a sound card is installed.

High Definition 8 channel audio
Supports SPDIF input/output
Audio CODEC: Realtek ALC888

Network

LAN: 10-Base-T

Interface: Integrated into motherboard
Technology: Intel 82562V
Data transfer speeds: up to 10/100Mb/s
Transmission standards:10-Base-T Ethernet

Expansion Slots

One PCI Express x16
Three PCI

I/O Ports

Back I/O ports

Figure : Back I/O panel

PS/2 mouse (green)

IEEE 1394a

RJ-45 Network (LAN)

Audio: Rear Speaker Out (black)

Audio: Center/Subwoofer port (yellow orange)

Audio: Line In (light blue)

Audio: Line Out (lime)

Audio: Microphone (pink)

Audio: Side Speaker Out (gray)

USB 2.0: 4

Video Graphics Adapter

Coaxial SPDIF Out

Coaxial SPDIF In

PS/2 keyboard (purple)

Internal Connectors

One 24-pin ATX power connector
One 4-pin ATX power connector
One PATA connector
Four SATA connectors
One floppy drive connector
Two 12v fan connector for CPU fan and System fan
One 9-pin header for power button, reset button, power LED, and HDD LED
One SPDIF-Audio output connector
One line input connector (interrupts line input on back panel, Vista capable, requires matching front audio jack module)
One 9-pin audio header for headphone-out and microphone-in (yellow, Vista capable, requires matching front audio jack module)
Two USB 2.0 connectors supporting 4 additional USB 2.0 ports
One IEEE 1394a header
One jumper for resetting BIOS settings
One jumper to disable BIOS password checking

Motherboard layout

Figure : layout

Clearing the BIOS settings

caution:
Do not change any jumper setting while the computer is on. Damage to the motherboard can result.

This motherboard has jumper to clear the Real Time Clock (RTC) RAM in CMOS. In the default (normal) position the jumper is on pins 2-3.

Figure : Jumper location

Clearing CMOS

To clear CMOS, follow these steps:

To clear CMOS settings, temporarily set jumper CLRTC to pins 1-2.
Wait 5-10 seconds and then return the jumper to pins 2-3.
When you startup the PC you will need to enter BIOS setup to reset any custom BIOS settings.

Clearing the BIOS password

The BIOS password is used to protect BIOS settings from unwanted changes. If the BIOS password has been forgotten, disable password checking to enter setup and change or erase the password.

To erase the BIOS password follow these steps:

Turn OFF the computer and unplug the power cord.
Locate the jumper labeled CLPWD. The jumper is found at the top edge of the motherboard, near the DIMM sockets. In the default (normal) position the jumper is on pins 2-3.
Move the jumper on jumper CLPWD to pins 1-2 to clear password.
Plug the power cord and turn ON the computer.
Hold down the F1 key during the startup process and enter BIOS setup to change or clear the password.
After changing or clearing the BIOS passwords, remember to reset the jumper to pins 2-3.

hp-feedback-input-portlet

Actions

hp-feedback-banner-portlet

Actions

hp-country-locator-portlet

Actions

Country/Region: Flag

United States

hp-detect-load-my-device-portlet

Actions

hp-hero-support-search

Actions

Examples: "LaserJet Pro P1102 paper jam", "EliteBook 840 G3 bios update"