hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Looking for Site Help?

    Learn about the features of the HP Customer Support site and how to use them to meet your online support needs. Click Here

     

    Information
    HP fraudulent caller alert - protect yourself from scams

    Learn what to do if you are contacted by fraudulent callers posing as HP representatives. This could be a scam; do not provide any personal information.

    View article

hp-concentra-wrapper-portlet

Actions
Loading...

HP Electrostatic Plotter - Crash Codes and Descriptions

Crash codes typically indicate a physical component failure. First, attempt to change the queue size on the plotter. If the plotter continues to display a crash code, a service call should be placed.
  warning:
DO NOT ATTEMPT TO SERVICE THIS PRODUCT! TO PLACE A SERVICE CALL, CONTACT HP SERVICE.
Front Panel Hex Code
Error
Suggested Remedy
01
Operating system crash
1
02
Bad interrupt
1
03
Miscellaneous processor exception
1, P
10, 11
Bad system ROM
P
12
Bad font ROM
P
13, 14
Bad swath RAM
S, I, M
15, 16
Bad refresh circuit
S
17
Dynamic bus-sizing failed
S
18
Bad swath-RAM bank selector
I, S
19
Bad pixel circuitry on swath RAM PCA
S
1B
Bad disk track buffer
C
1C
Disk communication failed
C, P, M
1D
RS-232-C loop test failed
I, M
1E
Disk read different from disk write
C
28, 29, 2A
Plot queue memory on processor corrupted
1, P, R, C, D
30, 31, 32, 33, 34, 35
Internal assertion/Processor memory corrupted
1, P
38
Attempt to fetch message for inactive task
1, P
39
RAM stack overflow
1, P
3A
Task not in runable RAM list
1, P
3B
Out of memory
1, P
40
Bad disk address or length to R/W routine
1, P, C
41
Disk does not respond to commands
1, C, P
42
Disk expected to be idle but is not
1, C
43
Spurious interrupt
1, C
44
Error in status register
C
46
Write retry limit exceeded
D, C
47
Spurious interrupt
C, P
48
Disk not ready after power-up
R, C, D
49
Disk error in demo during retry
R, C, D
4F
VRC met illegal opcode in vector data
R, P, C, D
50
Boss task received bad message
1, P
51
Engine task received bad message
1, P
52
Panel task received bad message
1, P
54
VRC resumed after it was finished
P
55
Byte arrived at engine UART
I
60
UART output collision
1, I
61
INDONE indicated byte available, GETBYTE received none
1, I
62
Engine reported Serial i/o command error
1
63
i/o - print engine timed out. Cycle power.
1
68
UART output collision
1, I
69
INDONE indicated byte available, GETBYTE received none
1, I
6A
Front panel reported SIO command error
P
6B
i/o to front panel timed out
F, I
70
Processor PCA failure
1, P, C, D
71
Firmware crash
1, P, C, D
72
Spurious interrupt
1, P, C, D
73
i/o DMA failure
1, I, C, D
74, 75
Swath-RAM failure
1, S, C, D
76
Processor PCA failure
1, P, C, D
77
Disk controller
1, C, D
8x, 9x
Indicates failure on disk controller PCA
1, C, D
Suggested Remedy. To be performed in order listed
C = Disk Controller
S = SWATH/RAM PCA
D = Disk Drive
R = Reformat Disk and retry
I = I/O DMA PCA
P = Processor PCA
M = Main/Interconnect PCA
1 = Change Queue Size, cycle power and retry

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Flag United States

hp-detect-load-my-device-portlet

Actions
Loading...