hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    HP fraudulent caller alert - protect yourself from scams

    Learn what to do if you are contacted by fraudulent callers posing as HP representatives. This could be a scam; do not provide any personal information.

    View article

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet 5si, 8000, and 8100 Printers - Setting Up and Installing the Optional Envelope Feeder

How to order the optional envelope feeder
To order the optional envelope feeder, click: HP Parts Store (HP Part # C3765-69501 ).
How to install the optional envelope feeder
  1. Remove the internal packaging spacers and packing tape from the Envelope Feeder.
    Figure : Removing the packaging spacers and tape
  2. Turn off the HP LaserJet printer (button out).
    Figure : Turning the printer off
  3. Open Tray 1 on the right side of the HP LaserJet printer.
    Figure : Opening Tray 1
  4. Remove the cover that is over the opening of the Envelope Feeder.
    Figure : Removing the envelope feeder cover
  5. Locate the pins on the Envelope Feeder and the corresponding holes on the HP LaserJet printer.
    Figure : Locating the envelope feeder pins and printer holes for the pins
  6. Align the Envelope Feeder with the corresponding printer rails.
    Figure : Aligning the envelope feeder
  7. Slide the Envelope Feeder into the HP LaserJet printer until it locks into place.
    Figure : Sliding the envelope feeder into the printer
  8. Pull out the envelope tray extender. The tray extender will help reduce jams.
    Figure : Pulling out the envelope tray extender
  9. Adjust the width guides to the size of the envelopes that are to be used.
    Figure : Adjusting the envelope feeder width guides
  10. Lift the envelope weight lever and insert the envelopes up to the fill mark.
    Figure : Inserting envelopes into the envelope feeder
  11. Lower the lever. The envelopes should be angled with the bottom of the stack closest to the HP LaserJet printer. Do not angle them in the opposite direction.
    Figure : Lowering the envelope weight lever onto the envelopes
  12. Turn on the HP LaserJet printer (button in).
    Figure : Turning the printer on
    Verify the installation by printing a configuration page as follows:
    HP LaserJet 8000 and 8100
    1. Ensure that the HP LaserJet printer is on and the READY message is displayed.
    2. Press MENU until the display reads INFORMATION MENU.
    3. Press ITEM until the display reads PRINT CONFIGURATION.
    4. Press SELECT to print the configuration page.
    5. The configuration page shows the HP LaserJet printer’s current configuration.
    HP LaserJet 5SI
    1. Ensure that the HP LaserJet printer is on and the READY message is displayed.
    2. Press MENUS until the display reads TEST MENU.
    3. Press ITEMS until the display reads PCL CONFIGURATION PAGE.
    4. Press SELECT to print the configuration page.
    5. The configuration page shows the HP LaserJet printer’s current configuration.
  13. Select the envelope type and size in the paper-handling menu on the HP LaserJet printer's control panel.
    Figure : Selecting the desired envelope type and size
    HP LaserJet 8000 and 8100
    1. Ensure that the HP LaserJet printer is on and the READY message is displayed.
    2. Press the MENU key until PAPER HANDLING MENU appears.
    3. Press the ITEM key until ENVELOPE FEEDER TYPE appears.
    4. Press the VALUE key until the desired type appears, then press SELECT.
    5. Press the ITEM key until ENVELOPE FEEDER SIZE appears.
    6. Press the VALUE key until the desired size appears, then press SELECT.
    7. Press the GO button to exit the menu.
    HP LaserJet 5si
    1. Ensure that the HP LaserJet printer is on and the READY message is displayed.
    2. Press the MENUS key until TRAY MENU appears.
    3. Press the ITEMS key until ENV FEEDER TYPE = appears.
    4. Press the VALUE key until the desired type appears, then press SELECT.
    5. Press the ITEMS key until ENV FEEDER SIZE = appears.
    6. Press the VALUE key until the desired size appears, then press SELECT.
    7. Press the On Line key to exit the menu.
      note:
    When printing envelopes make sure to choose an output destination other than a multibin mailbox. The envelope feeder will function correctly with a multibin mailbox attached to the printer but envelopes sent to a multibin mailbox will jam.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Flag United States

hp-detect-load-my-device-portlet

Actions
Loading...