Служба поддержки клиентов HP - База знаний

hp-contact-secondary-navigation-portlet

Действия
Загрузка...
  • Информация

    The website is under updating / веб-сайт оновлюється

    Информация
    Створіть аккаунт HP сьогодні!

    Швидше зв’язуйтесь зі службою підтримки HP, керуйте всіма своїми пристроями в одному місці, переглядайте інформацію про гарантію тощо. Дізнатись більше

    Информация

    Виправте та вирішіть проблему з оновленням Windows 10 на комп'ютері або принтері HP. Натисніть тут

HP Deskjet F4100 All-in-One Printer Series- Setting up the All-in-One (Hardware)

Introduction

This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.
This document includes the following steps to set up the product:
  • Unpack the All-in-One
  • Check the contents of the box
  • Connect the power cord and adapter
  • Turn on the power
  • Load plain paper
  • Install the cartridges
  • Align the cartridges

Setting up the All-in-One

Follow these steps in order. When you are finished, you can click the appropriate link at the end of this document if you need instructions to install the product software.

Step one: Unpack the All-in-One

  1. Lower the paper tray and remove all packing material.
    Рис. : Lower the paper tray
  2. Lower thecartridge door and remove all packing material.
    Рис. : Remove the packaging material

Step two: Check the contents of the box

The contents might vary by country/region. See the packaging for a list of items shipped in the box.

Step three: Connect the power cord and adapter

Connect the power cord and adapter.
Рис. : Connect the power cord and adapter

Step four: Turn on the power

  1. Press the On button ().
    Рис. : Press the On button
  2. Wait 30 seconds for the product to start up.

Step five: Load plain paper

  1. Pull out the tray extender.
    Рис. : Pull out the tray extender
  2. Load plain white paper.
    Рис. : Load plain white paper

Step six: Install the cartridges

  1. Open the cartridge door. Make sure the carriage moves to the center. If it does not move to the center, turn the product off and then turn it on again.
    Примечание.
    The product must be turned on to insert cartridges.
    Рис. : Open the cartridge door
  2. Remove the tape from both cartridges.
    Рис. : Remove the tape
      Внимание!
    Do not touch the copper-colored contacts or re-tape the cartridges.
    Рис. : Copper-colored contacts
  3. Hold the cartridges with the HP logo on top.
  4. Insert the tri-color cartridge in the left cartridge slot and the black cartridge in the right cartridge slot.
    Рис. : Carriage slots
    Рис. : Insert the tri-color cartridge in the left slot
  5. Make sure to push the cartridges in firmly until they snap into place.
    Рис. : Push the cartridge in firmly
    Рис. : Tri-color cartridge and black cartridge correctly installed
  6. Close the cartridge door.
    Рис. : Close the cartridge door

Step seven: Align the cartridges

Make sure that paper is loaded in the tray, and then wait a few minutes while the cartridge alignment page prints. After the alignment page prints, place it face-down on the glass and close the lid.
Рис. : Align the cartridges
Press the Scan button () to complete the alignment. Wait until the green On light stops blinking.


Страна/регион: Flag Україна

hp-detect-load-my-device-portlet

Действия
Загрузка...