HP ENVY 5540, DeskJet 5570 Printers - First Time Printer Setup

not:

If you are looking for the printer software, go to:

• Printer software for HP ENVY 5540 printers: http://123.hp.com/ENVY5540
• Printer software for HP DeskJet Ink Advantage 5575 printer: http://123.hp.com/DJ5575

1. Remove the printer from the box.
2. Remove all tape and packing materials from the outside of the printer.
   Şekil : Removing tape and packing materials from outside the printer

   
3. Remove the sticker from the printer control panel.
4. Lift up the scanner lid.
   Şekil : Opening the scanner lid

   
5. Remove all tape and packing materials from the scanner glass.
6. Close the scanner lid.
7. Open the ink cartridge access door by placing two fingers under one or both of the small handles on the sides of the ink cartridge access door and then lifting it up.
8. Remove all tape and packing materials from inside the printer.
   Şekil : Removing the tape and packing materials from inside the printer

   
9. Close the ink cartridge access door.
   Şekil : Closing the ink cartridge access door

   
10. Grasp the handle on the bottom of the paper tray, then pull to open the tray.
11. Lift up and pull out the output tray, then remove all tape and packing materials from the photo tray.
    Şekil : Removing all packing materials from the photo tray

    
12. With the paper tray pulled out, push in the photo tray.
    Şekil : Pushing in the photo tray

    
13. Slide out the paper width guides, then remove all tape and packing materials from inside the paper tray.
    Şekil : Removing all packing materials from inside the paper tray

    
14. Replace the output tray on the paper tray, then push in the paper tray until it locks into place.
    Şekil : Pushing in the paper tray

    
15. Discard or recycle the packing materials.

  dikkat:

Do not connect a USB cable at this time. The printer prompts you to connect the USB during the software installation.

1. Connect the power cord to the rear of the printer, then plug the other end of the power cord into an electrical outlet.
   Şekil : Connecting the power cord

   
2. Turn on the printer.
3. On the printer control panel, touch your preferred language, then touch OK to confirm your choice.
4. Touch your specific country/region, then touch OK.

1. Open the ink cartridge access door by placing two fingers under one or both of the small handles on the sides of the ink cartridge access door and then lifting it up. The Door Open screen displays on the printer control panel with the message 'The ink cartridge access door is open. Close the door to continue.'
   Şekil : Opening the ink cartridge access door

   
2. Remove one of the ink cartridges from its package. Be careful to only touch the black plastic on the ink cartridge.
   Şekil : Removing the ink cartridge from its package

   
3. Remove the protective tape.

     dikkat:

   Do not touch the copper-colored contacts or the ink nozzles. Do not replace the protective tape on the contacts. Handling these parts can result in clogs, ink failure, and bad electrical connections.

   Şekil : Removing the tape and avoiding touching the ink cartridge contacts or ink nozzles

   
4. Find the ink cartridge carriage on the right side of the printer, slide the new ink cartridge into the empty slot in the carriage, then gently push in the ink cartridge until it snaps into place.
   • Insert the tri-color ink cartridge into the left slot.
   • Insert the black ink cartridge into the right slot.
   Şekil : Inserting the new ink cartridge

   
5. Repeat these steps to install the other ink cartridge.
6. Close the ink cartridge access door. When the door is completely closed, the Door Open message disappears, and the printer control panel returns to the Home screen.
   Şekil : Closing the ink cartridge access door

   
7. Touch OK.
8. Wait for the printer to complete the calibration cycle.

1. Grasp the handle on the bottom of the input tray, and then pull the tray toward you to open it.
   Şekil : Opening the paper tray

   
   The Close Tray screen displays on the printer control panel with the message, 'A paper tray is open. Make sure the paper you want to use is loaded, and then close the tray to continue.'
2. With the paper tray pulled out, push in the photo tray as far as possible.
   Şekil : Pushing in the photo tray

   
3. Slide out the paper width guides as far as possible.
   Şekil : Sliding out the paper width guides

   
4. Load plain white paper U.S. letter or A4-sized paper into the paper tray.
5. Push the stack of paper toward the rear of the paper tray until the paper stops.
   Şekil : Sliding the paper back and the paper width guides in

   
6. Gently slide in the paper width guides until they lightly rest against the edges of the paper.
7. Push in the paper tray until it locks into place.
   Şekil : Pushing in the paper tray

   
8. Wait while the printer automatically prints an alignment page.
9. If the alignment page does not print, follow these steps to complete the alignment:
   1. On the printer control panel, swipe to the left, and then touch Setup .
   2. Touch Tools, and then touch Align Printer.
10. Lift the scanner lid, then place the alignment page with the print side down on the scanner glass. Position the alignment page according to the engraved guides around the glass.
11. Close the scanner lid, then touch OK.
    The printer scans the alignment page, completing the alignment.
12. Touch Finish, and then discard or recycle the alignment page.

• Printer software for HP ENVY 5540 printers: http://123.hp.com/ENVY5540
• Printer software for the HP DeskJet Ink Advantage 5575 printer: http://123.hp.com/DJ5575