hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

Removal and replacement: Control panel (X585)

This document provides instructions about removing and replacing the control panel.

Mean time to repair:8 minutes

Service level:Basic

Before performing service

Turn the printer power off

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cord before attempting to service the printer.

  • Disconnect either the USB cable or the network ethernet cable.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.

Part information

Control panel kit part number

5851-5952

Control panel kit with instruction guide

Required tools

No special tools are required to install this kit.

After performing service

Turn the printer power on

  • Reconnect either the USB cable or the network cable.

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Print a configuration page to make sure that the printer is functioning correctly.

Remove the control panel

Follow these steps to remove the control panel.

  1. Tilt the control panel up, and then open and remove the access cover.

    Open the control panel access cover

    Open the control panel access cover
  2. Remove one thumbscrew.

    Remove the thumbscrew

    Remove the thumbscrew
  3. Disconnect two cables.

    Note:

    Flow models have a third cable, a flat, flexible cable (FFC) for the keyboard. You do not need to detach this FFC.

    Disconnect two control panel cables

    Disconnect two control panel cables
  4. Slide the control panel to the left, and then carefully pull it away from the product to avoid damaging the cables.

    Remove the control panel

    Remove the control panel

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the control panel

Follow these steps to install the control panel.

  1. Reinstall the control panel.

    Install the control panel

    Install the control panel
  2. Reattach the cables.

    Reattach two cables

    Reattach two cables
  3. Reinstall the thumbscrew.

    Install one thumbscrew

    Install one thumbscrew
  4. Reinstall the contol panel access cover.

    Install the access panel

    Install the access panel

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Thailand

hp-detect-load-my-device-portlet

Actions
Loading...