HP EliteBook 2560p Notebook PC - Removing and Replacing the Hard Disk Drive

Error:

Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions.

hp-support-head-portlet

Actions

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions

hp-hero-support-search

Actions

Examples: "LaserJet Pro P1102 paper jam", "EliteBook 840 G3 bios update"

hp-share-print-widget-portlet

Actions

Information

Information regarding recent vulnerabilities
HP is aware of the recent vulnerabilities commonly referred to as "Spectre" and "Meltdown". HP has published a security bulletin with patches for these issues and a list of impacted systems. We will continue to update the bulletin as more information becomes available and encourage customers to check the bulletin frequently.

hp-concentra-wrapper-portlet

Actions

HP EliteBook 2560p Notebook PC - Removing and Replacing the Hard Disk Drive

Introduction

Minimum skill level

Parts required

Summary of instructions

Parts return

Introduction

This document is provided to assist in removing and replacing the hard disk drive for the HP EliteBook 2560p Notebook PC.

Minimum skill level

The end user requires no hardware-specific training to replace the defective part. The end user should have familiarity with system hardware and software requiring repair.

Parts required

note:

Part numbers are subject to change.

The replacement part number will vary depending on the hard disk drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.

Description	Part Number	Requires Return
750GB SATA hard disk drive - 7200 rpm, 2.5-inch form factor	633252-001 (Original)	Yes
500GB SATA hard disk drive - 7200 rpm	634925-001 (Modified)	Yes
320GB SATA hard disk drive - 7200 rpm	641672-001 (Modified)	Yes
320GB SATA hard disk drive - 7200 rpm, 2.5-inch form factor, 9.5-mm height (raw drive)	626978-001 (Modified)	Yes
250GB SATA hard drive - 7200 rpm, 2.5-inch form factor, 9.5-mm height	635225-001 (Modified)	Yes
160GB solid-state drive	651389-001 (Modified)	Yes
128GB solid-state drive	651388-001 (Modified)	Yes

note:

For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Summary of instructions

To view a video demonstrating the procedure for removing the hard disk drive, click on the link below. Or use the product video listing on the HP Services Media Library (Click here to go to HP Services Media Library), then select Hard disk drive from the menu on the upper left hand side of the screen.

Click here to view the hard disk drive removal video (right-click on the link to open in a new window/tab).

Hard disk drive removal

caution:

Observe all precautions when removing and replacing components.

Review the safety considerations before performing the steps listed below by clicking on the following link:

Click here to view the precautions.

caution:

Failure to comply with the precautions could result in damage to your product or loss of data.
Remove the battery. Click here for instructions on how to remove the battery.
Remove the service door. Click here for instructions on how to remove the service door.
Loosen the four captive P1 Phillips-head screws that secure the hard disk drive to the base enclosure.
Pull the Mylar tab out from under its storage slot on the hard disk drive carrier.
Lift the Mylar tab to disconnect the hard disk drive from the system board and lift it out of the base enclosure.
Remove the four 3-mm P1 Phillips-head screws that secure the hard disk drive carrier to the hard disk drive.
Lift and remove the hard disk drive from the hard disk drive carrier.
Disconnect the SATA adapter from the hard disk drive.
Place the hard disk drive in a static dissipative bag.

Hard disk drive replacement

Remove the hard disk drive from the static dissipative bag.
Connect the SATA adapter to the hard disk drive.
Place the hard disk drive on to the hard disk drive carrier.
Replace the four 3-mm P1 Phillips-head screws to secure the hard disk drive to the hard disk drive carrier.
Align the hard disk drive into the hard disk drive bay.
Press the hard disk drive down until it is fully seated into its connector on the system board.
Tighten the four captive P1 Phillips-head screws to secure the hard disk drive to the base enclosure.
Tuck the Mylar tab back into its storage slot on the hard disk drive carrier.
Replace the service door. Click here for instructions on how to replace the service door.
Replace the battery. Click here for instructions on how to replace the battery.