hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet M604, M605, M606 - Removal and replacement: Hard-disk drive (HDD)

This document provides the procedures to remove and replace the hard-disk drive.

Mean time to repair: 10 minutes

Service level: Intermediate

Before performing service

Turn the printer power off

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cord before attempting to service the printer.

  • Disconnect all network cables.

    CAUTION:

    This part contains components that are electrostatic discharge (ESD) sensitive. To reduce the possibility of ESD damage, always touch the sheet-metal chassis to ground yourself before touching an ESD-sensitive part.

    Important:

    Do not replace the formatter, DC controller, and eMMC PCA or hard-disk drive simultaneously during a single printer servicing. Doing so might cause the printer to become unstable or inoperable.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.

Part information

Hard-disk drive part number

B5L29-67901

Hard-disk drive kit

Required tools

  • No special tools are required to remove this part.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Make sure that the printer initializes to a Ready state.

Print a configuration page to make sure that the printer is functioning correctly.

Remove the formatter cover

Follow these steps to remove the formatter cover.

  1. Grasp the handle on the formatter cover (callout 1), and then slide the cover toward the rear of the printer to remove it.

    Remove the formatter cover

    Remove the formatter cover
  2. Open the formatter case door.

    Open the formatter case door

    Open the formatter case door

Remove the hard-disk drive

Follow these steps to remove the hard-disk drive.

  1. Locate the hard-disk drive (HDD) on the formatter.

    Locate the hard-disk drive

    Locate the hard-disk drive
  2. Release one tab (callout 1), grasp the HDD mounting bracket, and then rotate the connector end of the bracket up (callout 2) and away from the formatter to release it.

    Release the HDD

    Release the HDD
  3. Slide the HDD toward the front of the printer (callout 1) to release one tab (callout 2) from the slot (callout 3) in the formatter case, and then remove the HDD.

    Remove HDD

    Remove HDD

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the hard-disk drive

Follow these steps to install the hard-disk drive.

  1. Install the tab (callout 1) on the HDD bracket into the slot (callout 2) on the formatter case, and then slide the HDD toward the back of the printer (callout 3).

    Tip:

    If this is the first time the HDD is being installed, remove the pre-scored label that covers the slot in the chassis (callout 2).

    Install the tab

    Install the tab
  2. Rotate the HDD down toward the formatter and press down. Make sure that the retainer tab (callout 1) latches into the hole (callout 2) on the formatter, and that the connector latch (callout 3) snaps into the connector (callout 4).

    Install the HDD

    Install the HDD
  3. Verify that the HDD is fully seated in the connector (callout 1) and that the retainer tab (callout 2) is latched.

    Verify HDD installation

    Verify HDD installation

Install the formatter cover

Follow these steps to install the formatter cover.

  1. Close the formatter case door.

    Close the formatter case door

    Close the formatter case door
  2. Align the tabs (callout 1) on the formatter cover with the slots (callout 2) in the right cover, and then slide the formatter cover toward the front of the printer to install it.

    Align the tabs and slots

    Align the tabs and slots

Reinstall the product firmware

Follow these steps to reinstall the product firmware.

Note:

If this installation is a replacement HDD, use the following steps to reinstall the firmware.

Note:

To view installation instructions, go to http://www.hp.com/go/futuresmart. Select Upgrade now, and then select How to perform a firmware update.

  1. Go to www.hp.com/go/futuresmart.

  2. Select Upgrade now.

  3. Find your Enterprise printer model.

  4. Select the link to open the firmware download page.

  5. Select OS Independent from the list of operating systems.

  6. Under the Firmware section, find the file for multiple operating systems.

  7. Select Download.


hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Singapore

hp-detect-load-my-device-portlet

Actions
Loading...