HP OfficeJet 200 Mobile Printer - First Time Printer Setup

This document is for HP OfficeJet 200, 200c, 202, 202c Mobile printers.

To set up a printer for the first time, remove the printer and all packing materials from the box, install the battery, connect the power cable, set control panel preferences, load paper, and then install the ink cartridges. After your printer is set up, download and install the latest print driver.

note:

If you are looking for the printer software, go to 123.hp.com/OJ200.

The following video demonstrates how to set up the physical parts of the printer.

View the video on YouTube

The contents might vary by country/region. See the packaging for a list of items shipped in the box.

Remove the printer from the box and all tape, stickers, remove all packing materials from the printer, and then install the battery.

1. Remove the printer from the box.
2. Remove all tape and packing materials from the outside of the printer.
   Figure : Removing tape and packing materials
   
3. Lift the top cover, and then remove tape from the inside of the printer.
   Figure : Lifting the top cover and removing tape

   
4. Open the ink cartridge access door, and then remove all tape and packing material from inside the printer.
   Figure : Removing tape and packing materials from inside printer

   
5. Recycle the packing materials.

Depending on your printer model and the country/region it was sold in, it may have come with an optional lithium-ion rechargeable battery. If your printer did not come with a battery or you purchased one separately, skip to the next step to connect the power cord.

note:

To purchase a battery for your printer, visit the HP Store and search for your printer model.

1. Turn the printer so the rear faces you.
   Figure : Turning the printer

   
2. Push the battery cover latch to the right, and then pull the battery cover toward you to remove it.
   Figure : Removing the battery cover

   
3. Unwrap the battery.
   Figure : Unwrap the battery

   
4. Slide the battery into its slot, and then press the left side of the battery until it clicks into place.
   Figure : Pressing on the edge of the battery

   
5. Slide the battery cover into its slot, and then make sure the left side of the cover clicks into place.
   Figure : Installing the battery cover

   

Plug the printer into a wall outlet, turn on the printer, and then set your preferences.

note:

Do not connect a USB cable at this time. The connection to the computer is established during software installation.

1. Connect the power cord to the rear of the printer, and then plug the other end of the power cord into an electrical outlet.
   Figure : Connecting the power cord and power supply

   
2. Turn on the printer.
3. On the printer control panel, press the arrow buttons to select your preferred language and country/region, and then press OK.
   Figure : Selecting language from the control panel

   

Load plain, U.S. letter, or A4 paper in the input tray.

1. Open the top cover, and then lift the control panel.
2. Slide the two paper-width guides out as far as possible.
   Figure : Sliding paper-width guides out as far as possible

   
3. Load 50 sheets of plain paper or less into the paper tray, and then slide the paper-width guides until they rest against the sides ofthe paper.
   Figure : Sliding paper-width guides against the paper

   

Install the HP ink cartridges that came in the box with your printer.

1. Open the ink cartridge access door.
   Figure : Opening the ink cartridge access door

   
2. Wait until the carriage is idle and silent before you continue.
3. Remove the ink cartridge from its package. Be careful to only touch the black plastic on the ink cartridge.
   Figure : Removing the ink cartridge from its package

   
4. Remove the plastic tape from the ink cartridge.

     caution:

   Do not touch the copper-colored contacts or the ink nozzles.Do not replace the protective tape on the contacts. Handling these parts can result in clogs, ink failure, and bad electricalconnections.

   Figure : Removing the plastic tape

   

5. Insert the ink cartridge into its slot, and then press the ink cartridge until it latches into place.

   note:

   Install the color ink cartridge on the left and the black ink cartridge on the right.

   Figure : Closing the ink cartridge latch

   
6. Close the ink cartridge access door.
   Figure : Closing the ink cartridge access door

   
7. After installing the ink cartridges, the printer automatically prints an alignment page. Aligning the ink cartridges is necessary to achieve the best print quality.
   If an alignment page did not print, you can manually print an alignment page.
   1. From the home screen on the printer control panel, use the arrow buttons to select Setup, and then press OK.
   2. Press the down arrow to select Tools, and then press OK.
   3. Press the down arrow to select Align Printer, and then press OK.
      Aligning... displays on the control panel. The printer might beep or make mechanical noises, and then the printer prints an alignment page.

Your HP printer hardware is now set up, and you can install the printing software.

note:

Do not connect the printer to a computer until instructed to do so in the printing software.

Download the latest version of the printing software from 123.hp.com/OJ200.