1. Remove all packing tape from outside the product, and then remove the protective film from the control panel display.
   Figure : Remove outside packing tape and protective film

   
2. Remove all packing tape and packing material from inside the product.
   Figure : Remove inside tape and packaging

   

1. Connect the power adapter to the back of the product.
2. Connect the power cord to the power adapter.
3. Connect the other end of the power cord to an alternating current (AC) power outlet.

1. When the control panel displays the Language menu, touch the right arrow () to select the desired language, and then touch OK.
2. Touch the right arrow () to select Yes to confirm the selection.

     note:

   If the language selection is not correct, select No, and then select another language.

3. In the Set Country/Region menu, touch the right arrow () to select the desired country/region, and then touch OK.
4. Touch the right arrow () to select Yes to confirm the selection.

1. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage becomes idle and silent before continuing.
   Figure : Open the cartridge door

   
2. Lift the latch handle on the carriage until it stops.
   Figure : Lift the latch handle

   
3. Remove the printhead from its packaging.
   Figure : Remove printhead packaging

   

     caution:

   Do not touch the copper-colored contacts. Do not let the contacts touch any surface. Do not scratch the contacts while inserting the cartridges.

4. Hold the printhead upright with the color-coded icons facing up.
5. Lower the printhead into the product with the cartridge slots facing forward.
   Figure : Lower the printhead into the product

   
6. Slowly lower the carriage latch to secure the printhead.
   Figure : Lower the carriage latch

   

  caution:

When you first setup the product you must install the cartridges that shipped in the box. These cartridges are labeled SETUP, and they calibrate your product before the first print job. Failure to install the SETUP cartridges during the initial product setup causes an error.

1. Remove the cartridge from its packaging, and then pull the orange pull tab straight back to remove the plastic wrap.

   Figure : Remove the plastic wrap

   
2. Twist the orange cap counterclockwise to snap it off.
   Figure : Remove the orange cap

   
3. With the cartridge contacts facing the printhead, slide the cartridge into its slot by matching the colored icons on the cartridge with those on the printhead. Press down on the cartridge until it clicks into place.
   Figure : Slide the cartridge into its slot and then press down.

   
4. Repeat this procedure for each cartridge.
5. Close the cartridge door.
   Figure : Close the cartridge door.

   

1. Lower the paper tray.
2. Pull out the tray extender, and then flip open the paper catch.
   Figure : Tray extender and paper catch
   
   1. Tray extender
   2. Paper catch
3. Slide the paper width guide to its outermost position.
   Figure : Slide out the paper width guide

   
4. Load a stack of plain paper into the paper tray, print side down. Slide the stack of paper forward until it stops.
   Figure : Load paper in the tray

   

     note:

   Make sure all the paper in the stack is the same size and type and free from rips, dust, wrinkles, and curled or bent edges.

5. Slide the paper width guide inward until it stops at the edge of the paper.
   Figure : Slide the paper width guide inward

   

1. When prompted after loading the paper, touch OK on the control panel to print an alignment page. The product prints an alignment page.
   Figure : Example of an alignment page

   
2. Lift the product lid.
   Figure : Lift the lid.

   
3. Place the alignment page print side down on the right front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page.
   Figure : Place the alignment page on the scanner glass

   
4. Lower the lid.
5. Touch OK. The product scans the alignment page, completing the alignment.