hp-support-head-portlet

Acciones
Cargando...
Soporte al cliente de HP: base de conocimientos

hp-contact-secondary-navigation-portlet

Acciones
Cargando...

hp-share-print-widget-portlet

Acciones
Cargando...
  • Información

    Arregle y solucione problemas de actualización de Windows 10 en una Computadora o Impresora HP. Haga clic aquí

    Información

    ¿Problemas de audio o sonido? ¡Pruebe nuestro automatizado HP Audio check!

    Información
    ¡Cree una cuenta HP hoy!

    Conéctese con el soporte de HP de manera más rápida, administre todos sus dispositivos en un solo lugar, vea la información de garantía y más. Más información

hp-concentra-wrapper-portlet

Acciones
Cargando...

HP EliteBook 2540p Notebook PC - Removing and Replacing the 2.5-inch Storage Drive

Introduction

This document is provided to assist in removing and replacing the 2.5-inch storage drive for the HP EliteBook 2540p Notebook PC.

Minimum skill level

The End-User should possess product-specific knowledge and technical skill on how to service the system, and have familiarity with the operating system.

Tools required

Small, Phillips-head (P00 and P1) screwdrivers

Parts required

nota:
Part numbers are subject to change.
The replacement part number will vary depending on the 2.5-inch storage drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
80GB solid-state drive (SSD) - SATA interface, 2.5-inch form factor - For use only in the optical drive bay (Requires separate hard drive carrier)
602676-001 (Modified)
Yes
160GB solid-state drive (SSD) - SATA interface, 2.5-inch form factor - For use only in the optical drive bay (Requires separate hard drive carrier)
598783-001 (Modified)
Yes
250GB SATA II hard disk drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - For use only in the optical drive bay (Requires separate hard drive carrier)
598779-001 (Modified)
Yes
320GB SATA II hard disk drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - For use only in the optical drive bay (Requires separate hard drive carrier)
598780-001 (Modified)
Yes
500GB SATA II hard disk drive - 7,200 RPM, 2.5-inch form factor, 9.5 mm height - For use only in the optical drive bay (Requires separate hard drive carrier)
598781-001 (Modified)
Yes
nota:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Summary of instructions

To view a video demonstrating the procedure for removing the 2.5-inch storage drive, click on the link below. Or use the product video listing on the HP Services Media Library, (Click here to go to HP Service Media Library), then select 2.5-inch Storage drive from the menu on the upper left hand side of the screen.
Click here to view the 2.5-inch storage drive removal video(right-click on the link to open in a new window/tab).

2.5-inch Storage drive removal

  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      atención:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. Remove the 2.5-inch storage drive carrier.
  3. Remove the four 3 mm P1 Phillips-head screws that secure the 2.5-inch storage drive in the 2.5-inch storage drive carrier.
  4. Carefully lift the outside edge of the 2.5-inch storage drive until it clears the bezel and slide it toward the bezel to disconnect the 2.5-inch storage drive from its connector on the 2.5-inch storage drive carrier.
  5. Remove the 2.5-inch storage drive from the 2.5-inch storage drive carrier.
  6. Place the 2.5-inch storage drive in a static dissipative bag.

2.5-inch Storage drive replacement

  1. Remove the 2.5-inch storage drive from the static dissipative bag.
  2. At an angle, carefully toe the 2.5-inch storage drive into the 2.5-inch storage drive carrier and connect the 2.5-inch storage drive to its connector on the 2.5-inch storage drive carrier.
  3. Lower the 2.5-inch storage drive into the 2.5-inch storage drive carrier.
  4. Replace the four 3 mm P1 Phillips-head screws that secure the 2.5-inch storage drive in the 2.5-inch storage drive carrier.
  5. Replace the 2.5-inch storage drive carrier.

Parts return


hp-feedback-input-portlet

Acciones
Cargando...

hp-feedback-banner-portlet

Acciones
Cargando...

hp-country-locator-portlet

Acciones
Cargando...
País/región: Flag Puerto Rico

hp-detect-load-my-device-portlet

Acciones
Cargando...