hp-support-head-portlet

Acciones
Cargando...
Soporte al cliente de HP: base de conocimientos

hp-contact-secondary-navigation-portlet

Acciones
Cargando...

hp-share-print-widget-portlet

Acciones
Cargando...
  • Información

    Arregle y solucione problemas de actualización de Windows 10 en una Computadora o Impresora HP. Haga clic aquí

    Información

    ¿Problemas de audio o sonido? ¡Pruebe nuestro automatizado HP Audio check!

    Información
    ¡Cree una cuenta HP hoy!

    Conéctese con el soporte de HP de manera más rápida, administre todos sus dispositivos en un solo lugar, vea la información de garantía y más. Más información

hp-concentra-wrapper-portlet

Acciones
Cargando...

HP EliteBook 2540p Notebook PC - Removing and Replacing the 1.8-inch Storage Drive

Introduction

This document is provided to assist in removing and replacing the 1.8-inch storage drive for the HP EliteBook 2540p Notebook PC.

Minimum skill level

The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.

Parts required

nota:
Part numbers are subject to change.
The replacement part number will vary depending on the 1.8-inch storage drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
80GB solid-state drive (SSD) - SATA interface, 1.8-inch form factor - For use only in the hard drive bay, and on computer models equipped with a low-voltage (25 W) processor
602675-001 (Modified)
Yes
160GB solid-state drive (SSD) - SATA interface, 1.8-inch form factor - For use only in the hard drive bay, and on computer models equipped with a low-voltage (25 W) processor
598782-001 (Modified)
Yes
160GB SATA II hard disk drive - 5,400 RPM, 1.8-inch form factor, 9.5mm height - With bracket - For use only in the hard drive bay, and on computer models equipped with a low-voltage (25 W) processor
598777-001 (Modified)
Yes
250GB SATA II hard disk drive - 5,400 RPM, 1.8-inch form factor, 9.5mm height - With bracket - For use only in the hard drive bay, and on computer models equipped with a low-voltage (25W) processor
598778-001 (Modified)
Yes
nota:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Summary of instructions

To view a video demonstrating the procedure for removing the 1.8-inch storage drive, click on the link below. Or use the product video listing on the HP Services Media Library, (Click here to go to HP Service Media Library), then select 1.8-inch Storage drive from the menu on the upper left hand side of the screen.
Click here to view the 1.8-inch storage drive removal video (right-click on the link to open in a new window/tab).

1.8-inch Storage drive removal

  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      atención:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. Remove the 1.8-inch storage drive carrier.
  3. Disconnect the storage drive connector board from its connector on the 1.8-inch storage drive.
  4. Remove the rubber gasket that surrounds the 1.8-inch storage drive.
  5. Place the 1.8-inch storage drive in a static dissipative bag.

1.8-inch Storage drive replacement

  1. Remove the 1.8-inch storage drive from the static dissipative bag.
  2. Wrap the rubber gasket around the 1.8-inch storage drive.
  3. Connect the storage drive connector board into its connector on the 1.8-inch storage drive.
  4. Replace the 1.8-inch storage drive carrier.

Parts return


hp-feedback-input-portlet

Acciones
Cargando...

hp-feedback-banner-portlet

Acciones
Cargando...

hp-country-locator-portlet

Acciones
Cargando...
País/región: Flag Puerto Rico

hp-detect-load-my-device-portlet

Acciones
Cargando...