hp-support-head-portlet

Acciones
Cargando...
Soporte al cliente de HP: base de conocimientos

hp-contact-secondary-navigation-portlet

Acciones
Cargando...

hp-share-print-widget-portlet

Acciones
Cargando...
  • Información

    Solucione errores intermitentes en la cola de impresión/con el spooler de impresión que podrían causar fallos en los trabajos de impresión tras una actualización de Windows. Haga clic aquí

    Información
    Corrija errores en Win 10

    Resuelva problemas de actualización  de Windows 10  en un PC o impresora HP – haga clic aquí

hp-concentra-wrapper-portlet

Acciones
Cargando...

Removing and Replacing the Touchpad Board for HP ENVY 15-u000 x360 Convertible PCs

This document applies to HP ENVY 15-u000 x360 convertible computers.
HP ENVY 15-u000 x360 convertible computer

Before you begin

  • Have a Phillips head screwdriver, tweezers or needle-nose pliers, and a nonmetallic stick or similar prying tool.
  • Turn off the computer. Disconnect the Ethernet or modem cable. Disconnect the power cord.
  • Transfer the computer to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.
  • Do not remove a component from its protective packaging until you are ready to install it.
  advertencia:
Before starting, power off the computer and wait for components to cool before starting these procedures.
  atención:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
  atención:
Procedures in this document are provided by HP for qualified service agents and as a courtesy to its customers. Servicing internal components increases the risk of damaging the computer which might not be covered under warranty. Understand the risk and refer to the product's warranty before attempting to service the computer.

Video overview

View the following video before using the steps in this article.
nota:
The video and graphics in this article depict a specific configuration of notebook computer. These same removal and replacement procedures apply to all configurations for all HP ENVY 15-u000 x360 Convertible notebook computers.

Removing the touchpad board

Follow the steps in this section to remove the touchpad board.
  advertencia:
Make sure the computer is disconnected from power before starting.
Step 1
Remove the top cover.
For instructions to remove the top cover, see the HP support document, Removing and Replacing the Top Cover HP ENVY 15-u000 Convertible Notebook PCs.
Removing the top cover
Step 2
Find the touchpad board connector.
Finding the touchpad board
Step 3
Using minimal force, carefully lift the locking bar up on the touchpad board connector...
Lifting the locking bar on the touchpad board connector
... and disconnect the touchpad board ribbon cable from the touchpad board.
Disconnecting the touchpad ribbon cable from the touchpad board
Step 4
Remove the three Phillips broad-head screws that secure the touchpad board to the top cover.
Three screw locations
Step 5
Lift the top cover and gently release the touchpad board from the retention tab on the top cover.
Lifting the top cover to release the touchpad board
Step 6
Slide the tabs on the touchpad board out of the top cover and remove.
Sliding out the tabs on the touchpad board
Step 7
Place the touchpad board into a static dissipative bag.
Placing the touchpad board in a static dissipative bag

Replacing the touchpad board

Use the steps in this section to replace the touchpad board.
Step 1
With the top cover lifted, insert the tabs on the touchpad board into the touchpad board cradle in the top cover...
Lifting the top cover and inserting the tabs
...and apply pressure to the touchpad board to secure it with the retention tab.
Applying pressure to secure the touchpad board with the retention tab
Step 2
Replace the three Phillips broad-head screws that secure the touchpad board to the top cover.
Three screw locations
Step 3
Insert the touchpad board ribbon cable into the touchpad board connector on the touchpad board...
Inserting the
...and press the locking bar down to lock the cable into place.
Pressing down the locking bar
Step 4
Replace the top cover.
For instructions to replace the top cover, see the HP support document, Removing and Replacing the Top Cover HP ENVY 15-u000 Convertible Notebook PCs.
Replacing the top cover

hp-feedback-input-portlet

Acciones
Cargando...

hp-feedback-banner-portlet

Acciones
Cargando...

hp-country-locator-portlet

Acciones
Cargando...
País/región: Flag Perú

hp-detect-load-my-device-portlet

Acciones
Cargando...