hp-support-head-portlet

Acciones
Cargando...
Soporte al cliente de HP: base de conocimientos

hp-contact-secondary-navigation-portlet

Acciones
Cargando...

hp-share-print-widget-portlet

Acciones
Cargando...
  • Información
    Solucione problema de impresora HP en macOS

    El mensaje "Un [componente de software] dañará su computadora" aparece durante la impresión o instalación - Haga clic aquí

    Información

    ¿Problemas de audio o sonido? ¡Pruebe nuestro automatizado HP Audio check!

    Información

    Arregle y solucione problemas de actualización de Windows 10 en una Computadora o Impresora HP. Haga clic aquí

    Información
    ¡Cree una cuenta HP hoy!

    Conéctese con el soporte de HP de manera más rápida, administre todos sus dispositivos en un solo lugar, vea la información de garantía y más. Más información

hp-concentra-wrapper-portlet

Acciones
Cargando...

HP Z400 Workstation - Removing and Replacing the PCI card

This document pertains only to HP Z400 Workstations with the following case design:

Before you begin

  • Turn off the workstation, and then disconnect all cables. Disconnect the Ethernet or modem cable before disconnecting the power cord.
  • Move the workstation to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the workstation.
  • Do not remove a component from its protective packaging until you are ready to install it.
  advertencia:
The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the workstation.
  atención:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.

Video overview (in English)

To view a video demonstrating the procedure for removing the PCI card, right-click PCI card removal video and select Open link in new window/tab.

Replacement part information

The following HP part numbers are known to be compatible with this system:
nota:
Part numbers are subject to change.
Description
Part Number
Requires Return
PCIe ATI FirePro V7750 Workstation graphics accelerator card - With 1 GB 128-bit GDDR3 memory and High Dynamic Range (HDR) rendering - DirectX 10.1 and OpenGL 2.0 supported
519293-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 4800 graphics card - With 1 GB 256-bit GDDR3 memory, 602 MHz core clock, and 150W TDP
536796-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 4800 graphics card - With 1 GB 256-bit GDDR3 memory, 602 MHz core clock, and 150W TDP
492188-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 5800 graphics card - With 2 GB 512-bit GDDR3 memory, 650 MHz core clock, and 189W TDP (Gen 2.0)
536797-001 (Modified)
Yes
PCIe ATI FirePro V3700 Workstation graphics accelerator card - With 256 MB 64-bit GDDR3 memory and High Dynamic Range (HDR) rendering - DirectX 10.1 and OpenGL 2.0 supported
519291-001 (Modified)
Yes
PCIe ATI FirePro V5700 Workstation graphics accelerator card - With 512 MB 128-bit GDDR3 memory and High Dynamic Range (HDR) rendering - DirectX 10.1 and OpenGL 2.0 supported
519292-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 380 graphics card - With 256 MB 128-bit GDDR3 memory, 34W TDP
519294-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 580 graphics card - With 512 MB 128-bit GDDR3 memory, 40W TDP
519295-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 1800 graphics card - With 768 MB 192-bit memory, 59W TDP
519296-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro FX 3800 graphics card - With 1 GB 192-bit memory, 59W TDP
519297-001 (Modified)
Yes
PCIe 3D NVIDIA Quadro NVS 295 graphics card - With 256 MB 64-bit DDR2 memory, 21W TDP. Low profile
519298-001 (Modified)
Yes
DVI-I to VGA adapter - From a (M) DVI-I connector to a (F) 15-pin VGA connector - For connecting a VGA monitor to a DVI-I port on the graphics board
202997-001 (Modified)
Yes
PCIe Sound Blaster X-Fi Xtreme Gaming sound card
493346-001 (Modified)
Yes
Broadcom NetXtreme Gigabit Ethernet Plus network adapter card - 10BaseT/100Base-TX/1000Base-T, 1Gbps data transfer rate, PCIe x1, one RJ-45 connector
488293-001 (Modified)
Yes
PCI Express x4 (4-port) Serial Attached SCSI (SAS) and Serial ATA RAID interface card
510359-001 (Modified)
Yes
PCIe IEEE 1394b Firewire interface card
508927-001 (Modified)
Yes
PCIe IEEE 1394 firewire card, full height
515182-001 (Original)
Yes
* If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. For more information about returning parts to HP select one of the links below:
nota:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

PCI card removal

Step 1
With all cables disconnected from the workstation, remove the access panel.
For more information about removing the access panel, refer to the HP support document Instructions on how to remove the access panel.
Step 2
Disconnect any cables attached to the PCI card.
Step 3
Press on the two green PCI retention clamp clips until they release.
Step 4
Rotate the PCI retention clamp up against the rear of the chassis.
Step 5
Lift straight up on the PCI card to remove it from the slot.
nota:
If the PCI slot has a locking tab, push out and hold the locking tab while lifting the PCI card.
Step 6
If the PCI card is not replaced with another, cover the open slot in the PCI card cage with a metal slot cover to facilitate proper airflow and cooling of the system.

PCI card replacement

Step 1
If installing a new PCI card, remove the slot cover from the appropriate slot on the PCI bulkhead.
Step 2
Align the connectors on the PCI card with the slot on the system board.
Step 3
Press down on the PCI card until it is fully seated in the slot on the system board.
Step 4
Rotate the PCI retention clamp down over the PCI card bulkhead.
Step 5
Press in on the two green PCI card retention clamp tabs on the rear of the chassis until they lock into place.
Step 6
Connect any cables to the PCI card.
Step 7
Replace the access panel.

hp-feedback-input-portlet

Acciones
Cargando...

hp-feedback-banner-portlet

Acciones
Cargando...

hp-country-locator-portlet

Acciones
Cargando...
País/región: Flag Perú

hp-detect-load-my-device-portlet

Acciones
Cargando...