This document pertains only to HP Z400 Workstations with the following case design:
hp-support-head-portlet
Acciones
- ${title}
Cargando...
Soporte al cliente de HP: base de conocimientos
hp-contact-secondary-navigation-portlet
Acciones
- ${title}
Cargando...
hp-share-print-widget-portlet
Acciones
- ${title}
Cargando...
hp-concentra-wrapper-portlet
Acciones
- ${title}
Cargando...
HP Z400 Workstation - Removing and Replacing the Hard drive
Before you begin
-
Turn off the workstation, and then disconnect all cables. Disconnect the Ethernet or modem cable before disconnecting the power cord.
-
Move the workstation to a clear, flat, stable work surface over a non-carpeted floor.
-
HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the workstation.
-
Do not remove a component from its protective packaging until you are ready to install it.
advertencia:The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the workstation.
atención:This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
Video overview (in English)
To view a video demonstrating the procedure for removing the hard drive, right-click Hard drive removal video and select Open link in new window/tab.
Replacement part information
The following HP part numbers are known to be compatible with this system:
nota:Part numbers are subject to change.
|
Description
|
Part Number
|
Requires Return
|
|
1TB SATA hard drive - 7,200 RPM, 3.5 inches form factor, and NCQ (Native Command Queuing) technology
|
508027-001 (Original)
|
Yes
|
|
146 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM
|
405430-001 (Modified)
|
Yes
|
|
300 GB SATA SQ hard drive - 7,200 RPM, 3.5 inches form factor, 1.0 inch high
|
453139-001 (Modified)
|
Yes
|
|
160 GB SATA SQ hard drive - 10,000 RPM, 3.5 inches form factor, 1.0 inch high
|
508029-001 (Modified)
|
Yes
|
|
250 GB SATA SQ hard drive - 7,200 RPM, 3.5 inches form factor, 8 MB cache
|
508028-001 (Original)
|
Yes
|
|
HP 300 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor, 1.0 inch high
|
413647-001 (Modified)
|
Yes
|
|
320 GB SATA hard drive - 7,200 RPM, 3.5 inches form factor, and NCQ (Native Command Queuing) technology
|
508026-001 (Original)
|
Yes
|
|
450 GB hot-plug Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor
|
495608-001 (Modified)
|
Yes
|
|
HP 300 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor, 1.0 inches high
|
460579-001 (Modified)
|
Yes
|
|
300 GB SATA SQ hard drive - 10,000 RPM, 3.5 inches form factor, 1.0 inch high
|
502599-001 (Modified)
|
Yes
|
* If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. For more information about returning parts to HP select one of the links below:
nota:For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.
Hard drive removal
|
Step 1
With all cables disconnected from the workstation, remove the access panel.
For more information about removing the access panel, refer to the HP support document Instructions on how to remove the access panel.
|
|
|
Step 2
Disconnect the power and data cables from the drive.
|
|
|
Step 3
Pull out on the green release latch and slide the drive out of the drive cage.
|
|
|
Step 4
If the replacement drive does not include guide screws, remove and reuse the screws from this drive or use the spare screws provided on the drive cage.
|
|
Hard drive replacement
|
Step 1
Align the guide screws on the drive with the guide slots in the drive bay.
|
|
|
Step 2
Push the drive into the bay until it locks into place.
|
|
|
Step 3
Connect the power and data cables to the drive.
|
|
|
Step 4
Replace the access panel.
|
|
Otras opciones de soporte técnico
{{#each this}}
{{#if (eq ../this.length 3)}}
{{else if (eq ../this.length 2)}}
{{else}}
{{/if}}
{{/each}}
hp-feedback-input-portlet
Acciones
- ${title}
Cargando...
hp-feedback-banner-portlet
Acciones
- ${title}
Cargando...
hp-country-locator-portlet
Acciones
- ${title}
Cargando...
País/región:
Perú
Perú
hp-detect-load-my-device-portlet
Acciones
- ${title}
Cargando...
hp-hero-support-search
Acciones
- ${title}
Cargando...
