Error:

Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions.

hp-support-head-portlet

Actions

HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions

hp-share-print-widget-portlet

Actions

Information

Need Windows 11 help?
Check the information on compatibility, upgrade, and available fixes from HP and Microsoft. Windows 11 Support Center

Feedback

hp-concentra-wrapper-portlet

Actions

Loading Paper and Envelopes for HP Color LaserJet Pro MFP M176n and M177fw Printers

Introduction

This document provides instructions for loading plain paper, short-length paper, and envelopes in the printer.

Load plain paper

Remove the dust cover from the input tray.

Figure : Remove the dust cover
Slide the paper guides to their outermost positions.

Figure : Slide the paper guides out
Load a stack of U.S. letter or A4 size paper into the input tray with the short edge forward and the print side up. Push the stack into the tray until it stops.

Figure : Load paper into the input tray
Slide in the paper guides until they rest against the edges of the paper.

note:
Do not push the paper guides so far in that they bind the paper.

Figure : Slide the paper guides in
Reinstall the dust cover on the input tray.

Figure : Reinstall the dust cover

Load shorter paper sizes

To print on paper shorter than 185 mm (7.3 in), use the short-paper extender to modify the input tray.

Remove the dust cover from the input tray.

Figure : Remove the dust cover
Remove any paper from the paper tray.
Slide the paper guides to their outermost positions.

Figure : Slide the paper guides out
Remove the short-paper extender tool from the storage slot on the right side of the input area.

Figure : Remove the short-paper extender tool
Slide the tabs on the short-paper extender tool into the slots in the paper length guide until the guide snaps into place.

Figure :
Push the paper into the printer until it stops, and then push the paper length guide in so the extender tool rests against the paper.

Figure : Push the paper length guide in
Slide in the paper width guides until they rest against the edges of the paper.

Figure : Slide the paper guides in
When you finish printing on short paper, remove the short-paper extender tool from the input tray, and then place it in the storage slot.

Figure : Remove and store the short-paper extender tool
Reinstall the dust cover on the input tray.

Load envelopes

Before you load and print on envelopes, review the following guidelines.

Envelope Guidelines

Do not use envelopes with clasps, snaps, windows, coated linings, self-stick adhesives, or other synthetic materials that are susceptible to heat.
Do not use envelopes that are wrinkled, nicked, stuck together, or otherwise damaged.
If you use envelopes with peel-off adhesive strips, make sure they are approved for use in laser printers.
Only use envelopes recommended for laser printers.
Use envelopes with seams that extend to the corners.
Acceptable

Unacceptable

Remove the dust cover from the input tray.

Figure : Remove the dust cover
Remove any paper from the input tray.
Slide the paper guides to their outermost positions.

Figure : Slide the paper guides out
Remove any paper from the input tray.
Load envelopes in the middle of the tray with the print side facing up and the stamp end towards you.

Figure : Load enveloped in the middle of the tray
Slide in the paper guides until they rest against the edges of the envelope.

note:
Do not move the paper guides so far in that they bind the envelope.
Reinstall the dust cover on the input tray.

hp-feedback-input-portlet

Actions

hp-feedback-banner-portlet

Actions

hp-country-locator-portlet

Actions

Country/Region: Flag

New Zealand

hp-detect-load-my-device-portlet

Actions

hp-hero-support-search

Actions

Examples: "DeskJet 3630 paper jam", "ProBook 440 G2 bios update"