This document provides the procedure to install the optional 1 x 550-sheet paper feeder with stand for the HP Color LaserJet Enterprise M652, M653, and HP Color LaserJet Enterprise MFP M681, M682 printers.
-
Take the 1 x 550-sheet paper feeder with stand out of the box, and then remove the packaging material. Verify that the contents match this illustration:
note:
HP recommends recycling packing materials whenever possible.Figure : Contents of the box
-
Press the Power button to turn OFF the printer.Figure : Turn off the printer
-
Disconnect the power cord and the USB cable or network cable.Figure : Disconnect the cables
-
Place the printer on the 1 x 550-sheet paper feeder with stand. Use the alignment pins on top of the stand to position the printer.
caution:
HP recommends that three people move the printer to place it on the stand.All trays must be closed when moving the printer.Figure : Place the printer on the paper feeder with stand
-
Open the tray and then turn the tray lock clockwise.Figure : Open the tray and turn the tray lock
-
Remove the tape and shipping restraint from the tray.Figure : Remove tape and shipping restraint
-
Adjust the paper-width and paper-length guides by squeezing the blue adjustment latches and sliding the guides to the size of paper being used.Figure : Adjust the paper guides
-
Load paper into the tray. Be sure that the top of the stack is below the tray-full indicator.Figure : Load paper in the tray
-
Adjust the paper guides by grasping the adjustment latches and pressing inward. Check the paper to verify the guides lightly touch the stack, but do not bend it.Figure : Adjust the paper guides to rest lightly against the stack of paper
-
Remove the tray number cube from the back side of the tray face plate.Figure : Remove the tray number cube
-
Reinsert the tray number cube into its slot with the number three facing outward. The number three should show on the front right side of the tray.Figure : Reinsert the tray number cube with the number three facing outward
-
Close the tray.Figure : Close the tray
-
Unscrew the stabilizing foot on the bottom of the printer stand so it rests on the floor and supports the printer.
note:
The stabilizing foot should place enough pressure on the floor to prevent the printer from rolling.Figure : Unscrew the stabilizing foot to support the printer
-
Reconnect the power cord and the USB cable or network cable.Figure : Reconnect the cables
-
Press the Power button to turn on the printer.Figure : Turn on the printer
-
Configure the accessory in the software print driver. Find your operating system in the options below, and then follow the steps provided.
-
OS X: The list of installed options should automatically update during the first print job after installing the accessory. If not, perform the following steps:
-
From the Apple menu (
), click System Preferences.
-
Select Print & Scan (or Printers & Scanners).
-
Select the printer, click Options & Supplies, and then click the Options tab.
-
Manually configure the accessory.
-
-
Windows® 8.0, 8.1, and 10: When attaching the accessory after installing the printer software, perform the following steps:
-
Windows® 8.0 and 8.1: Scroll to the bottom-left corner of the screen, and right-click the window that displays.Windows® 10: Right-click the Windows icon in the lower-left corner of the desktop.
-
Select Control Panel. Under Hardware and Sound, select View devices and printers.
-
Right-click the name of the printer, and then select Printer Properties.
-
Click the Device Settings tab.
-
Update the installed options. The steps vary according to connection type and print driver:
-
Network or USB connections with the HP Universal Print Driver (UPD): In the Installable Options section under Automatic Configuration, select Update Now
-
Network or USB connections with the HP PCL 6 print driver: Select Update Now.
-
Network or USB connections with the HP PCL-6 version 4 print driver: Manually install the accessory by clicking the drop-down menu next to the tray to be installed, and then select HP 550-sheet Input Tray.
-
-
-
Windows® 7: When attaching the accessory after installing the printer software, perform the following steps:
-
Make sure the printer is turned on and connected to the computer or network.
-
Open the Windows Start menu, and then click Devices and Printers.
-
Right-click the name of this printer, and select Printer Properties.
-
Click the Device Settings tab.
-
Update the installed options. The steps vary according to connection type and print driver:
-
Network or USB connection with the HP Universal Print Driver (UPD): In the Installable Options section under Automatic Configuration, select Update Now.
-
Network or USB connections with the HP PCL 6 print driver: Select Update Now.
-
-
-
Windows® XP and Windows Vista®: When attaching the accessory after installing the printer software, perform the following steps:
-
Make sure the printer is turned on and connected to the computer or network.
-
Open the Windows Start menu, and then click Devices and Printers (or Printers and Faxes for XP).
-
Right-click the name of this printer, and select Printer Properties (or Properties for XP).
-
Click the Device Settings tab.
-
Click the Installable Options section.
-
To update the installed options for a Network or USB connection, in the drop-down menu next to Automatic Configuration, select Update Now.
-
-
