hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP PageWide Enterprise Color MFP 586 - Removal and replacement: Document feeder retention clips (586)

note:
This guide shows the HP LaserJet Enterprise MFP M527. However, the instructions are also valid for the HP PageWide Enterprise Color MFP 586.

Introduction

This document provides the procedures to remove and replace the document feeder retention clips (586).

Before performing service

Turn the printer power off
  • Disconnect the power cable.
      warning:
    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.
Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.
Retention clip kit part number
G1W41-67904
Retention clips with instruction guide

Required tools

  • No special tools are needed to remove or install these assemblies.

After performing service

Turn the printer power on
  • Connect the power cable.
  • Use the power switch to turn the power on.

Post service test

No post service test are available for this assembly.

Step 1: Remove the retention clips

note:
This guide shows the HP LaserJet Enterprise MFP M527. However, the instructions are also valid for the HP PageWide Enterprise Color MFP 586.
  1. Open the document feeder.
    Figure : Open the document feeder
  2. Pull down on the white backing to remove it.
    Figure : Remove the white backing
  3. If any of the retention clips (callout 1) remain attached to the white backing remove them. Otherwise, go to step Release any damaged retention clips..
    Figure : Check the white backing
  4. Release any damaged retention clips.
    note:
    Use the edge of a coin to loosen the clip.
    Figure : Release damaged clips
  5. Remove the retention clip.
    Figure : Remove the clip

Step 2: Unpack the replacement assembly

  1. Dispose of the defective part.
    note:
    HP recommends responsible disposal of the defective part.
  2. Unpack the replacement part from the packaging.
      caution:
    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands or before touching rollers or pads.
    note:
    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

Step 3: Install the retention clips

  1. If a spring comes off of a retention clip, make sure that it is correctly repositioned on the clip.
    Figure : Check the clip spring
  2. Install the clip (callout 1) in the opening (callout 2) in the document feeder.
    Figure : Install the clip
  3. Press the clip to make sure it is securely installed.
    Figure : Press the clip
  4. Place the white backing on the scanner glass.
    note:
    Place the corner of the backing that does not have a hook-and-loop fastener in the upper-left corner of the scanner glass.
    Figure : Place the white backing on the glass
  5. Close the document feeder.
    Figure : Close the document feeder
  6. Open the document feeder and make sure that the white backing is securely attached.
    Figure : Check the white backing
  7. Close the document feeder.
    Figure : Close the document feeder

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Malaysia

hp-detect-load-my-device-portlet

Actions
Loading...