hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Information regarding recent vulnerabilities

    HP is aware of the recent vulnerabilities commonly referred to as "Spectre" and "Meltdown". HP has published a security bulletin with patches for these issues and a list of impacted systems. We will continue to update the bulletin as more information becomes available and encourage customers to check the bulletin frequently.

hp-concentra-wrapper-portlet

Actions
Loading...

HP Compaq 8510w Mobile Workstation - Removing and Replacing the Hard Disk Drive

Introduction
This document is provided to assist in removing and replacing the Hard disk drive for the HP Compaq 8510w Mobile Workstation.
Minimum skill level
The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.
Tools required
P0 Phillips-head screwdriver.
P1 Phillips-head screwdriver.
Parts required
  note:
Part numbers are subject to change.
The replacement part number will vary depending on the Hard disk drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
160GB SATA hard drive - 7200 RPM, 9.5 mm form factor - Includes bracket and connector
455954-001 (Modified)
Yes
160GB SATA hard drive - 5400 RPM, 9.5 mm form factor - Includes bracket and connector
443920-001 (Modified)
Yes
120GB SATA hard drive - 7200 RPM, 9.5 mm form factor - Includes bracket and connector
455079-001 (Modified)
Yes
120GB SATA hard drive - 5400 RPM, 9.5 mm form factor - Includes bracket and connector
443919-001 (Modified)
Yes
100GB SATA hard drive - 7200 RPM, 9.5 mm form factor - Includes bracket and connector
452200-001 (Modified)
Yes
80GB SATA hard drive - 7200 RPM, 9.5 mm form factor - Includes bracket and connector
445939-001 (Modified)
Yes
80GB SATA hard drive - 5400 RPM, 9.5 mm form factor - Includes bracket and connector
443918-001 (Modified)
Yes
  note:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.
Summary of instructions
To view a video demonstrating the procedure for removing the Hard disk drive, click on the link below. Or use the product video listing on the HP Services Media Library (Click here to go to HP Services Media Library), then select Hard disk drive from the menu on the upper left hand side of the screen.
Click here to view the Hard disk drive removal video (Right-click on the link to open in a new window/tab).
Hard disk drive removal
  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      caution:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. Loosen the two captive P0 Phillips-head screws that secure the Hard disk drive cover to the bottom of the notebook.
  3. Use your finger or a flat-bladed tool to lift the inside edge of the Hard disk drive cover and remove it.
  4. Loosen the captive spring-loaded P1 Phillips-head screw that secures the Hard disk drive.
  5. Grasp the Mylar tab and pull the Hard disk drive toward the outside edge of the base enclosure to disconnect the Hard disk drive from the system board connector.
  6. Lift the Hard disk drive out of the bay and remove.
  7. Place the Hard disk drive in a static dissipative bag.
Hard disk drive replacement
  1. Remove the Hard disk drive from the static dissipative bag.
  2. Place the Hard disk drive into the Hard disk drive bay.
  3. Push the Hard disk drive toward the inside of the base enclosure until the connector is seated.
  4. Tighten the captive spring-loaded P1 Phillips-head screw that secures the Hard disk drive.
  5. Toe the Hard disk drive cover into the enclosure.
  6. Tighten the two captive P0 Phillips-head screws.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Malaysia

hp-detect-load-my-device-portlet

Actions
Loading...