hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Looking for Site Help?

    Learn about the features of the HP Customer Support site and how to use them to meet your online support needs. Click Here

     

hp-concentra-wrapper-portlet

Actions
Loading...

HP Compaq dx2300 Microtower PC - Removing and Replacing the PCI card

Introduction
This document is provided to assist in removing and replacing the PCI card for the HP Compaq dx2300 Microtower PC.
Minimum skill level
The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.
Tools required
Torx-15 screwdriver.
Parts required
  note:
Part numbers are subject to change.
The replacement part number will vary depending on the PCI card that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
ATI Radeon X1300 PCI-Express graphics board - Video board with 256 MB DDR SDRAM memory, one DVI-I digital display output, and one 4-pin (F) mini-DIN (S-video) TV output
413023-001 (Modified)
Yes
PCIe ATI Radeon X1300 (RV516) graphics controller card - 256 MB DDR2 SDRAM, dual-head
432747-001 (Modified)
Yes
Belkin wireless LAN (Rest Of World) 802.11a/b/g PCI card
391866-001 (Modified)
Yes
Belkin wireless LAN (Americas) 802.11a/b/g PCI card
391866-002 (Modified)
Yes
IEEE 1394 (FireWire) low profile interface card - 400, 200, 100 Mbps data rates
393308-001 (Modified)
Yes
Intel Pro/1000 PT Gigabyte Ethernet PCIe network interface card - Has one RJ-45 connector
398754-001 (Modified)
Yes
Agere Systems PCI SoftModem - High-speed 56 Kbps, V.92 modem card
398661-001 (Modified)
Yes
DVI-I to VGA adapter - From a (M) DVI-I connector to a (F) 15-pin VGA connector
202997-001 (Modified)
Yes
  note:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.
Summary of instructions
To view a video demonstrating the procedure for removing the PCI card, click on the link below. Or use the product video listing on the HP Services Media Library then select PCI card from the menu on the upper left hand side of the screen.
Click here to view the PCI card removal video (right-click on the link to open in a new window/tab).
PCI card removal
  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      caution:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. Disconnect any cables attached to the PCI card.
  3. Remove the Torx-15 screw and then lift and remove the PCI retention clamp on the rear of the chassis.
  4. Pull straight up on the card to remove it from the PCI slot.
      note:
    If not replacing the PCI card with another card, cover the open slot on the PCI bulkhead with a metal slot cover.
PCI card replacement
  1. If you are installing a new PCI card, remove the slot cover from the appropriate slot on the PCI bulkhead.
  2. Align the connectors on the PCI card with the PCI slot on the system board.
  3. Press the card firmly into the slot. Make sure the card is seated properly.
  4. Insert the tabs on the PCI retention clamp into the slots on the chassis and lower the clamp into place.
  5. Replace the Torx-15 screw to secure the clamp to the chassis.
  6. Connect any cables needed to the PCI card.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Flag Latvia

hp-detect-load-my-device-portlet

Actions
Loading...