HP ENVY 7640, Officejet 5740, 8040 Printers - Loading Paper, Envelopes, and Index Cards

1. Grasp the handle on the input tray, and then pull the tray toward you to open it. The Close Tray screen displays on the printer control panel with the message, 'A paper tray is open. Close the tray to continue. Touch to view paper loading instructions.'
   Figura : Pull out the input tray

   
2. Touch the Play icon () on the bottom left corner of the touchscreen to watch a video on loading paper (optional).
3. With the input tray pulled out, push in the photo tray as far as possible.
   Figura : Push in the photo tray

   
4. Remove any paper from the input tray that is different than the type of paper you want to load, and then slide out the paper width guides as far as possible.
   Figura : Slide out the paper width guides

   

   Nota:

   If you want to load legal size paper, lower the front of the input tray. Locate the latch that is inside the front of the tray on the left. Slide the latch upward, and then lower the front of the tray.

   Figura : Lower the front side of the input tray to load legal size paper

   
5. Insert a small stack of paper into the tray. Make sure that the print side is face-down with the short edge forward.
   Figura : Load paper in the input tray

   
6. Push the paper toward the rear of the input tray until the paper stops, and then, if necessary, gently slide the paper width guides inward so that they lightly rest against the edges of the paper.
   Figura : Slide the paper back and the paper width guides in

   

   Nota:

   Make sure that the stack of paper is not higher than the top edges of the paper width guides.

7. Push the input tray into the printer until it locks into place.
   Figura : Push in the input tray

   
8. The Have You Changed the Paper? screen displays. If you do not touch an option, the message fades after several seconds, and the printer uses the last paper settings that were entered. Follow these steps to adjust the paper settings as needed.
   • If you did not change the paper size or type, touch OK to return to the Home screen, or wait several seconds to allow the printer to automatically return to the Home screen.
   • If you did change the paper size or type, touch Main Tray, touch Paper Size, and then touch your paper size. Touch Paper Type, and then touch your paper type. Touch Done, and then touch OK to return to the Home screen.

1. Grasp the handle on the input tray, and then pull the tray toward you to open it. The Close Tray screen displays on the printer control panel with the message, 'A paper tray is open. Close the tray to continue. Touch to view paper loading instructions.'
   Figura : Pull out the input tray

   
2. Touch the Play icon () on the bottom left corner of the touchscreen to watch a video on loading paper (optional).
3. With the input tray pulled out, push in the photo tray as far as possible.
   Figura : Push in the photo tray

   
4. Remove any paper from the input tray that is different than the envelopes you want to load, and then slide out the paper width guides as far as possible.
   Figura : Slide out the paper width guides

   
5. Insert the envelopes into the center of the input tray with the envelope flap on the left and facing up. If the flap is on the short end of the envelope, insert the envelope into the center of the tray with the flap away from the printer and facing up.
   Figura : Example of how to load envelopes into the printer

   
6. Push the envelopes toward the rear of the input tray until the envelopes stop, and then gently slide the paper width guides inward so that they lightly rest against the edges of the envelopes. Make sure that the envelopes are centered in the tray.
   Figura : Push in the envelopes

   

   Nota:

   Make sure that the stack of envelopes is not higher than the top edges of the paper width guides.

7. Push the input tray into the printer until it locks into place.
   Figura : Push in the input tray

   
8. The Have You Changed the Paper? screen displays. If you do not touch an option, the message fades after several seconds, and then the printer uses the last paper settings that were entered. Follow these steps to adjust the paper settings as needed.
   • If you did not change the envelope size or type, touch OK to return to the Home screen, or wait several seconds to allow the printer to automatically return to the Home screen.
   • If you did change the envelope size or type, touch Main Tray, touch Paper Size, and then touch your paper size. Touch Paper Type, and then touch your paper type. Touch Done, and then touch OK to return to the Home screen.

1. Grasp the handle on the input tray, and then pull the tray toward you to open it. The Close Tray screen displays on the printer control panel with the message, 'A paper tray is open. Close the tray to continue. Touch to view paper loading instructions.'
   Figura : Pull out the input tray

   
2. Touch the Play icon () on the bottom left corner of the touchscreen to watch a video on loading paper (optional).
3. With the input tray pulled out, push in the photo tray as far as possible.
   Figura : Push in the photo tray

   
4. Remove any paper from the input tray that is different than the index cards you want to load, and then slide out the paper width guides as far as possible.
   Figura : Slide out the paper width guides

   
5. Insert a small stack of index cards into the center of the input tray. Make sure that the print side is face-down with the short edge forward.
6. Push the index cards toward the rear of the input tray until the cards stop, and then gently slide the paper width guides inward so that they lightly rest against the edges of the cards. Make sure that the cards are centered in the tray.
   Figura : Push in the index cards

   

   Nota:

   Make sure that the stack of index cards is not higher than the top edges of the paper width guides.

7. Push the input tray into the printer until it locks into place.
   Figura : Push in the input tray

   
8. The Have You Changed the Paper? screen displays. If you do not touch an option, the message fades after several seconds, and then the printer uses the last paper settings that were entered. Follow these steps to adjust the paper settings as needed.
   • If you did not change the paper size or type, touch OK to return to the Home screen, or wait several seconds to allow the printer to automatically return to the Home screen.
   • If you did change the paper size or type, touch Main Tray, touch Paper Size, and then touch your paper size. Touch Paper Type, and then touch your paper type. Touch Done, and then touch OK to return to the Home screen.

Nota:

The HP Officejet 8040 e-All-in-One Printer series has adjustable paper width guides in the photo tray and can also support other photo paper sizes.

1. Grasp the handle on the input tray, and then pull the tray toward you to open it. The Close Tray screen displays on the printer control panel with the message, 'A paper tray is open. Close the tray to continue. Touch to view paper loading instructions.'
   Figura : Pull out the input tray

   
2. Touch the Play icon () on the bottom left corner of the touchscreen to watch a video on loading paper (optional).
3. Put one or two fingers in the slot on the photo tray, and then pull the tray toward you to open it as far as possible.

   Nota:

   If you do not see the photo tray inside the input tray, remove the output tray, and then pull open the photo tray.

   Figura : Remove the output tray and pull open the photo tray

   
4. Remove any paper from the photo tray that is different than the photo paper you want to load. If the photo tray has adjustable paper width guides, gently slide out the paper width guides as far as possible.
5. Insert the photo paper print-side down into the photo tray. For photo paper with a perforated tab, place the paper in the tray print-side down with the perforated tab closest to you.
   Figura : Example of how to load photo paper into the printer

   
   Figura : Load the photo paper

   

   Nota:

   Make sure that the stack of photo paper is not higher than the top edges of the paper width guides.

6. If the photo tray has adjustable paper width guides, gently slide the paper width guides inward so that they lightly rest against the edges of the photo paper. Make sure that the photo paper is centered in the tray.
7. Push the photo tray into the printer as far as possible.
   Figura : Push in the photo tray

   
8. Replace the output tray on the input tray, if you removed it, and then push the input tray into the printer until it locks into place.
   Figura : Replace the output tray and push in the input tray

   
9. On the Have You Changed the Paper? screen that displays, check to make sure that the photo paper is correctly loaded into the photo tray.
   • If 4x6 in., Photo Paper displays in the Photo Tray field, the photo paper is loaded correctly in the photo tray. Touch OK to return to the Home screen, or wait several seconds to allow the printer to automatically return to the Home screen.
   • If the Photo Tray field displays as Empty, open the photo tray and make sure that the photo paper is pushed all the way to the rear of the tray, and then push the photo tray into the printer as far as possible. Push the input tray into the printer until it locks into place, and then check the touchscreen to make sure that 4x6 in., Photo Paper displays in the Photo Tray field.