HP Customer Support - Knowledge Base




  • Information
    Important Print Security Update

    HP was recently made aware of a vulnerability in certain InkJet and LaserJet printers by a third-party researcher. HP has updates available for download to address the vulnerability. Details and more information are available in the  Security Bulletin.


    Ensure your printer has the latest firmware to get product enhancements and fixes. More details for updating firmware here

    Need Windows 11 help?

    Check documents and videos on compatibility, FAQs, upgrade information and available fixes. Windows 11 Support Center

  • Feedback



HP DeskJet 2600 Printers - 'Out of Paper' Displays, Printer Does Not Pick Up Paper

This document is for HP DeskJet 2620, 2621, 2622, 2623, 2624, 2630, 2632, 2633, 2634, 2635, 2636,2640, 2652, 2655, 2680, DeskJet Ink Advantage 2675, 2676, 2677, 2678, and 2679 All-in-One printers:
The Error icon, the Paper Error icon, and the Resume light are on, a Load Paper message displays on the computer, and the printer does not pick up paper from the input tray.
The Error icon, the Paper Error icon, and the Resume light are on

Video overview

This video shows what to do when the printer does not pick up paper from the input tray.

Step 1: Check the paper, and then reload it

Paper feed issues might result from using ripped, dusty, curled, wrinkled, or bent paper. The quality of the paper can also make a difference. Use these guidelines to help avoid the issue.
  • Use only good quality paper that meets printer specifications.
  • Store all paper in a dry, cool place. Paper feed issues occur more often in humid environments.
  • Do not print on paper that is already printed. The dampness of the ink can cause the paper to stick together.
  • Wait for the printer to complete a job or for an Out of paper or Load Paper message to display before you reload the paper.
Make sure the paper you use to print is in good condition, is neatly stacked in the tray, and the paper path and tray are free from obstructions.
  1. Remove any paper from the input tray.
  2. Remove any severely bent, wrinkled, or torn paper from the stack.
  3. Check for obstructions inside the input tray area. Make sure nothing blocks the paper from engaging with the rollers. Even small pieces of paper can cause paper feed issues.
  4. With both hands, hold the stack of paper, and then tap the bottom edge of the stack on a flat surface so that the stack is even on all sides.
  5. Load the stack of paper into the input tray, and then slide in the paper-width guides against the paper.
    Sliding paper-width guides against the paper
Try to print. If the issue persists, continue to the next step.

Step 2: Clean the paper feed rollers

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.
  1. Turn off the printer, and then disconnect the power cord and any other cables.
    You must unplug the power cord to move the carriage by hand and reset the paper feed mechanism without the risk of electrical shock.
  2. Raise the input tray.
     Raising the input tray
  3. Lift and hold the input tray shield.
  4. Look down through the open input tray and find the gray paper pick rollers. You might need a flashlight to illuminate the area.
    Paper pick rollers
  5. Lightly dampen a cotton swab with water, and then squeeze any excess liquid from the swab.
  6. Press the swab against the rollers, and then rotate them upward with your fingers. Apply a moderate amount of pressure to remove dust or dirt buildup.
  7. Lower the input tray shield.
  8. Allow the rollers to dry completely (approximately 10 minutes).
  9. Reconnect the power cord and any other cables, and then turn on the printer.
Try to print. If the issue persists, continue to the next step.

Step 3: Reset the printer

Sometimes an error persists even though there is no paper feed issue. Reset the printer, and then try to print.
  1. With the printer turned on, disconnect the power cord from the printer.
  2. Unplug the power cord from the power source.
  3. Wait 60 seconds.
  4. Reconnect the power cord to a wall outlet and to the printer.
    HP recommends plugging the printer directly into a wall outlet.
Try to print. If the error persists, continue to the next step.

Step 4: Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.
Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.
To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.






Country/Region: Flag India