solution Contentsolution Content

HP Photosmart 2600 and 2700 All-in-One Printer Series- Setting up the All-in-One (Hardware)


This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.
This document includes the following steps to set up the product:
  • Unpack the product and check the contents of the box
  • Attach the control-panel overlay (if not attached)
  • Load plain white paper
  • Connect the power cord and telephone cord
  • Turn the All-in-One on
  • Install the cartridges
  • Set the date and time

Setting up the All-in-One

Follow these steps in order.

Step one: Unpack the product and check the contents of the box

Remove the tape from the outside of the product and check the components that came with your product.
The contents might vary by country/region. See the packaging for a list of items shipped in the box.

Step two: Attach the control-panel overlay (if not attached)

  1. Position the control panel overlay above the product.
    איור : Position the control panel overlay
  2. Press down firmly on all edges and in the center of the overlay to secure it.
    איור : Press down firmly
  3. Lift the color graphics display. For best viewing, remove the protective film from the display.
    איור : Lift the color graphics display

Step three: Load plain white paper

  1. Remove the output tray.
    איור : Remove the output tray
  2. Slide the paper width guide all the way to the left, and then pull the paper length guide as far away from the product as possible.
    איור : Slide the paper width and length guides
  3. Insert a stack of plain white letter or A4 paper into the paper tray, and then slide the paper guides snugly against the paper.
    איור : Insert paper
  4. Replace the output tray.
    איור : Replace the output tray

Step four: Connect the power cord and telephone cord

  1. Connect the power cord and adapter.
    איור : Connect the power cord and adapter
  2. Connect one end of the supplied telephone cord to the port on the left (1-LINE) and the other to a wall jack. To connect an answering machine or to use a different telephone cord, see the User Guide.
    איור : Connect the telephone cord

Step five: Turn the All-in-One on

Press the On button. The green light flashes, and then becomes solid. This might take up to a minute.
איור : The On button
Wait for the cartridge prompt before continuing.

Step six: Install the cartridges

You must leave the product turned on to install or remove the cartridges.
  1. Lift the access door until it stops.
    איור : Open the access door
  2. Press down and lift up the green and black latches on the carriage.
    איור : Open the latches
  3. Pull the pink tab to remove the tape from both cartridges.
    איור : Removing the tape from the cartridges
      שים לב:
    Do not touch the copper-colored contacts or re-tape the cartridges. This can damage the cartridges.
  4. With the label facing up, insert each cartridge into the carriage, and then push it in firmly until it stops.
    • Insert the tri-color cartridge in the left slot
    • Insert the black cartridge in the right slot.
    איור : Insert the cartridges
    איור : Correct cartridge placement
  5. Push down on the latches to close them, and then close the access door.
  6. Press OK at each of the prompts on the control panel to start the cartridge alignment process.
    The alignment might take a few minutes. After the page prints, alignment is complete.
  7. Check the display for the status, and then press OK. Recycle or discard the alignment page.

Step seven: Set the date and time

Follow these steps if you need to reset the date and time on your product:
  1. Press the Setup button, press 4, and then press 1.
    איור : Setup button
  2. Enter the month, day, and year by pressing the appropriate numbers on the keypad. Depending on your country/region setting, you might enter the date in a different order.
  3. Enter the hours and minutes.
    If your time is displayed in the 12-hour format, the AM or PM prompt automatically appears after you enter the last digit.
  4. If prompted, press 1 for AM, or 2 for PM.
    The new date and time settings appear on the display.