solution Contentsolution Content

HP Ink Tank 310, 410 printers - 'E4' error (Paper Jam)

An HP Ink Tank 310, 311, 315, 316, 318, 319, Wireless 410, 411, 412, 415, 416, 418, and 419 printer stops feeding pages and an E4 displays on the control panel.

Additionally the Error icon , Paper Error icon , and Resume light blink.

Note:

Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper. The following steps apply to both real and false paper jams.

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Clear jammed paper from the printer

Paper jams can occur in multiple areas of the printer. If you cannot find the paper jam in one area, continue to the next area until the jam is located.

Clear jammed paper from the input tray

Remove any jammed paper that is accessible from the input tray area.

Remove any loose paper from the input tray.
Press the Cancel button to try and automatically clear the jam.

If the error persists, continue with these steps to manually clear the jam.
Gently pull out any jammed paper from the input tray using both hands.
Remove any other torn pieces of paper or foreign objects from inside the input tray.
Reload a stack of paper into the input tray.
Press the Resume button on the control panel to continue the print job.

Clear jammed paper from the output tray

Remove any jammed paper that is accessible from the output tray area.

Press the Cancel button to try and automatically clear the jam.

If the error persists, continue with these steps to manually clear the jam.
Gently pull out any jammed paper from the output tray with both hands.
Remove any other torn pieces of paper or foreign objects from inside the tray area.
Press the Resume button on the control panel to continue the print job.

Clear jammed paper from the printhead access area

Remove any jammed paper from inside the printer.

Press the Cancel button to try and automatically clear the paper jam.

If the error persists, continue with these steps to manually clear the jam.
Turn off the printer, and then disconnect the power cord and the USB cord, if connected.

Warning:
To avoid risk of injuries or electric shock, you must disconnect the power cord before reaching inside the printer.
Close the output tray extender, and then push the output tray into the printer.
Open the exterior door, and then open the printhead access door.
Make sure the printhead latch is completely closed and the carriage is not obstructed.

CAUTION:
If the printhead latch is closed, do not press down on it.
If the printhead carriage is in the center of the printer, slide it to the right.
Gently pull out any jammed paper using both hands.
Remove any other torn pieces of paper or foreign objects from inside the printer.
Close the printhead access door, and then close the exterior door.
Pull out the output tray, and then lift the tray extender.
Reconnect the power cord and the USB cable, if necessary, and then turn on the printer.

Clear jammed paper from underneath the printer

Remove jammed paper from the paper path on the bottom of the printer.

Note:

Only perform these steps if the printer continues to report a paper jam after clearing jammed paper from the input and output trays and printhead access area. These steps require turning the printer on its back, and might result in ink leakages.

Press the Cancel button to try and automatically clear the jam.

If the error persists, continue with these steps to manually clear the jam.
Turn off the printer, and then disconnect the power cord and the USB cord, if connected.

Warning:
To avoid risk of injuries or electric shock, you must disconnect the power cord before reaching inside the printer.
Lower the paper input tray back into the printer, close the output tray extender, and then push the output paper tray into the printer.
Make sure the ink tank plugs are inserted and secure.
While using one hand to hold the scanner lid, slowly lift the printer, and then rest it on its back so you can access the underside (base).

CAUTION:
Do not turn the printer on its side. Turning the printer on its right or left side causes ink leakage.
Pull the tabs on either side of the cleanout door to open it.
Remove any jammed paper found inside the printer.
Close the cleanout door. Gently push the door forward until it snaps into place.
Turn the printer over to its normal position.
Reconnect the power cord and the USB cable, if necessary, and then turn on the printer.

Make sure the carriage can move freely

Make sure the carriage can move from one side of the printer to the other with no obstructions.

Turn on the printer.
Open the exterior door, and then open the printhead access door.
With the printer turned on, disconnect the power cord from the printer.

Warning:
To avoid risk of injuries or electric shock, you must disconnect the power cord before reaching inside the printer.
Check for and remove any paper or objects that might be restricting the carriage.
Check for and remove any paper from the rollers. If the paper tears when removed, check for and remove torn bits of paper in the rollers and wheels.
Without engaging the printhead latch, reach inside the printer and manually move the carriage.
- If the carriage is stuck on the right side of the printer, move the carriage to the left side of the printer.
- If the carriage is stuck on the left side of the printer, move the carriage to the right side of the printer.
- If the carriage is stuck in the middle of the printer, move the carriage to the right side of the printer.
Remove any loose paper or obstructions you find.
Make sure the carriage can move freely across the width of the printer. Firmly push the carriage to the left side of the printer, and then to the right side.
Close the printhead access door, and then close the exterior door.
Reconnect the power cord and turn on your printer.

Use an automated tool to clean ink smears

Clean ink smears with the automated tool in the printer to clear jams and optimize print quality.

Turn on the printer.
Load paper into the input tray.
Press and hold the Power button, press the Cancel button three times, press the Start Color Copy button eight times, and then release the Power button.

The printer feeds one page and makes noise for about one minute.

Manually clean the paper rollers inside the printer

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.

Turn off the printer, and then disconnect the power cord.

Warning:
To avoid risk of injuries or electric shock, you must disconnect the power cord before reaching inside the printer.
Raise the input tray.
Lift and hold the input tray shield.
Look down through the open input tray and find the gray paper pick rollers. You might need a flashlight to illuminate the area.
Lightly dampen a cotton swab with water, and then squeeze any excess liquid from the swab.
Press the swab against the rollers, and then rotate them upward with your fingers. Apply a moderate amount of pressure to remove dust or dirt buildup.
Lower the input tray shield.
Allow the rollers to dry completely (approximately 10 minutes).
Reconnect the power cord and turn on your printer.

Reset the printer

Reset the printer to recover from printer errors or failures.

With the printer turned on, disconnect the power cord from the printer.
Unplug the power cord from the power source.
Wait 60 seconds.
Reconnect the power cord to a wall outlet and to the printer.

Note:
HP recommends plugging the printer directly into a wall outlet.
Turn on the printer to complete the reset.

Learn how to avoid paper jams and feed issues

Follow these tips to help prevent paper jams, misfeeds, and no feeds.

Make sure the paper loaded in the input tray lays flat and the edges are not bent or torn.
When adding paper to the input tray, adjust the paper guide to rest against the edge of the paper stack.
Do not overfill the input tray, but make sure you have at least 5 pages loaded for best results.
Only use paper that is compatible with your printer. Use HP paper for optimal performance.
Whenever you change the paper size or type in the tray, make sure to change the paper settings on the software application you are printing from.
Do not combine different paper types or paper sizes in the input tray. The entire stack must be the same size and type.
Avoid using the printer in dusty or dirty environments.
Wait for the printer to complete a job or to display a Load Paper in Tray message before you load more paper.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Additional support options

Try one of our automated tools or diagnostics

Ask a question on our HP Support Community page

Get in touch with one of our support agents

Enter a topic to search our knowledge library

What can we help you with?

Need Help?