hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP Enterprise M607-M609, M610-M612, HP LaserJet Managed E60055-E60075, E60155-E60175 - Removal and replacement: Control panel (4.3 inch display)

This document provides the procedures to remove and replace the control panel (4.3 inch display).

Mean time to repair: 5 minutes

Service level: Basic

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part number

Part description

5851-7252

Control panel kit (109.22 mm 4.3 in display)

Required tools

  • #2 Phillips screwdriver with a magnetic tip

  • Small flat blade screwdriver

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

No post service test is available for this assembly.

Remove the control panel (4

3 inch display).

  1. Raise the control panel screen in the direction indicated by the arrow.

    Raise the control panel screen

    Raise the control panel screen
  2. Do the following:

    • Use a coin, or a small flat-blade screwdriver, to release the control panel cover in the direction indicated by the arrow.

    • Remove the control panel cover.

      Lift and remove the control panel cover

      Lift and remove the control panel cover
  3. Remove one thumbscrew (callout 1).

    Note:

    Store the screw in a secure place where it cannot fall down into the printer.

    Remove one thumbscrew

    Remove one thumbscrew
  4. Do the following:

    • Lift the back edge of the control panel up (callout 1).

    • Slide the control panel toward the back of the printer (callout 2) to release it.

      Lift and release the control panel

      Lift and release the control panel
  5. Do the following:

    • Turn the control panel over to gain access to the bottom side.

    • Disconnect two connectors (callout 1).

      Disconnect two connectors from the bottom side

      Disconnect two connectors from the bottom side
  6. Remove the control panel.

    Remove the control panel

    Remove the control panel

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the control panel (4

3 inch display).

  1. On the replacement control panel, connect two connectors (callout 1).

    Connect two connectors

    Connect two connectors
  2. Install the tabs, on the front of the control panel, into the slots on the printer top cover.

    Install the control panel tabs into the printer slots

    Install the control panel tabs into the printer slots
  3. Do the following:

    • Lower the back edge of the control panel down (callout 1).

    • Install one screw(callout 2).

      Lower the control panel and install one screw

      Lower the control panel and install one screw
  4. Do the following:

    • Align the tabs on the front of the control panel cover with the slots in the printer.

    • Pivot the cover down, in the direction indicated by the arrow, to install it.

      Align the control panel cover and pivot down to install it

      Align the control panel cover and pivot down to install it

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Ireland

hp-detect-load-my-device-portlet

Actions
Loading...