hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information
    Fix HP Printer issue on macOS

    A [software component] will damage your computer message displays when printing or while installing - Click Here

    Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP CM8060/CM8050 Color MFP with Edgeline Technology - Initial Setup menu

The Initial Setup menu has three sub-menus:
  • Networking and I/O menu
  • Fax Setup menu
  • E-mail Setup menu
note:
This menu is also available through the embedded Web server. In the embedded Web server, select the Settings tab, and then select Configure Device from the menu on the left side of the screen. See Use the embedded Web server.
note:
Values that have an asterisk (*) are the factory-default values. Some menu items have no default.

Networking and I/O menu

Networking and I/O menu
Menu item
Sub-menu item
Values
Description
I/O Timeout
Select a value in the range. The factory default setting is 15 seconds.
I/O timeout refers to the elapsed time before a print job fails. If the stream of data that the device receives for a print job gets interrupted, this setting indicates how long the device will wait before it reports that the job has failed.
Parallel Input
note:
This item appears only if an EIO accessory is installed.
High Speed
No
Yes*
Use the High Speed setting to configure the speed that the parallel port uses to communicate with the host.
Advanced Functions
Enabled*
Disabled
Use the Advanced Functions setting to enable or disable bi-directional parallel communication.
Embedded Jetdirect
EIO <X> Jetdirect
Embedded Jetdirect and EIO <X> Jetdirect menus
Menu item
Sub-menu item
Sub-menu item
Values and Description
TCP/IP
Enable
Off: Disable the TCP/IP protocol.
On*: Enable the TCP/IP protocol.
Host Name
An alphanumeric string, up to 32 characters, used to identify the device. This name is listed on the HP Jetdirect configuration page. The default host name is NPIxxxxxx, where xxxxxx is the last six digits of the LAN hardware (MAC) address.
IPV4 Settings
Config Method
Specifies the method that TCP/IPv4 parameters will be configured on the HP Jetdirect print server.
Bootp: Use BootP (Bootstrap Protocol) for automatic configuration from a BootP server.
DHCP*: Use DHCP (Dynamic Host Configuration Protocol) for automatic configuration from a DHCPv4 server. If selected and a DHCP lease exists, DHCP Release and DHCP Renew menus are available to set DHCP lease options.
Auto IP: Use automatic link-local IPv4 addressing. An address in the form 169.254.x.x is assigned automatically.
Manual: Use the Manual Settings menu to configure TCP/IPv4 parameters.
DHCP Release
This menu appears if Config Method was set to DHCP and a DHCP lease for the print server exists.
No*: The current DHCP lease is saved.
Yes: The current DHCP lease and the leased IP address are released.
DHCP Renew
This menu appears if Config Method was set to DHCP and a DHCP lease for the print server exists.
No*: The print server does not request to renew the DHCP lease.
Yes: The print server requests to renew the current DHCP lease.
Manual Settings
(Available only if Config Method is set to Manual) Configure parameters directly from the printer control panel:
IP Address: The unique IP address of the printer, where n is a value from 0 to 255.
Subnet Mask: The subnet mask for the printer, where m is a value from 0 to 255.
Syslog Server: The IP address of the syslog server used to receive and log syslog messages.
Default Gateway: The IP address of the gateway or router used for communications with other networks.
Idle Timeout: The time period, in seconds, after which an idle TCP print data connection is closed (default is 270 seconds, 0 disables the timeout).
Default IP
Specify the IP address to default to when the print server is unable to obtain an IP address from the network during a forced TCP/IP reconfiguration (for example, when manually configured to use BootP or DHCP).
Auto IP: A link-local IP address 169.254.x.x is set.
Legacy: The address 192.0.0.192 is set, consistent with older HP Jetdirect devices.
Primary DNS
Specify the IP address (n.n.n.n) of a Primary DNS Server.
Secondary DNS
Specify the IP address (n.n.n.n) of a Secondary Domain Name System (DNS) Server.
IPV6 Settings
Enable
Use this item to enable or disable IPv6 operation on the print server.
Off*: IPv6 is disabled.
On: IPv6 is enabled.
Address
Use this item to manually configure an IPv6 address.
Manual Settings: Use the Manual Settings menu to enable and manually configure a TCP/ IPv6 address.
Enable: Select this item and choose On to enable manual configuration, or Off to disable manual configuration.
Address: Use this item to type a 32 hexadecimal digit IPv6 node address that uses the colon hexadecimal syntax.
DHCPV6 Policy
Router Specified: The stateful auto-configuration method to be used by the print server is determined by a router. The router specifies whether the print server obtains its address, its configuration information, or both from a DHCPv6 server.
Router Unavailable: If a router is not available, the print server should attempt to obtain its stateful configuration from a DHCPv6 server.
Always: Whether or not a router is available, the print server always attempts to obtain its stateful configuration from a DHCPv6 server.
Primary DNS
Use this item to specify an IPv6 address for a primary DNS server that the print server should use.
Secondary DNS
Use this item to specify an IPv6 address for a secondary DNS server that the print server should use.
Proxy Server
Specifies the proxy server to be used by embedded applications in the device. A proxy server is typically used by network clients for Internet access. It caches Web pages, and provides a degree of Internet security, for those clients.
To specify a proxy server, enter its IPv4 address or fully-qualified domain name. The name can be up to 255 octets.
For some networks, you may need to contact your Independent Service Provider (ISP) for the proxy server address.
Proxy Port
Type the port number used by the proxy server for client support. The port number identifies the port reserved for proxy activity on your network, and can be a value from 0 to 65535.
IPX/SPX
Enable
Off: Disable the IPX/SPX protocol.
On*: Enable the IPX/SPX protocol.
Frame Type
Selects the frame-type setting for your network.
Auto: Automatically sets and limits the frame type to the first one detected.
EN_8023, EN_II, EN_8022, and EN_SNAP: Frame-type selections for Ethernet networks
AppleTalk
Enable
Off: Disable the AppleTalk protocol.
On*: Enable the AppleTalk protocol.
DLC/LLC
Enable
Off: Disable the DLC/LLC protocol.
On*: Enable the DLC/LLC protocol.
Security
Print Sec Page
Yes: Prints a page that contains the current security settings on the HP Jetdirect print server.
No*: A security settings page is not printed.
Secure Web
For configuration management, specify whether the embedded Web server will accept communications using HTTPS (Secure HTTP) only, or both HTTP and HTTPS.
HTTPS Required: For secure, encrypted communications, only HTTPS access is accepted. The print server will appear as a secure site.
HTTP/HTTPS optional: Access using either HTTP or HTTPS is permitted.
IPSEC
Specify the IPsec or Firewall status on the print server.
Keep: IPsec/Firewall status remains the same as currently configured.
Disable: IPsec/Firewall operation on the print server is disabled.
Reset Security
Specify whether the current security settings on the print server will be saved or reset to factory defaults.
No*: The current security settings are maintained.
Yes: Security settings are reset to factory defaults.
Diagnostics
Embedded Tests
This menu provides tests to help diagnose network hardware or TCP/IP network connection problems.
Embedded tests help to identify whether a network fault is internal or external to the device. Use an embedded test to check hardware and communication paths on the print server. After you select and enable a test and set the execution time, you must select Execute to initiate the test.
Depending on the execution time, a selected test runs continuously until either the device is turned off, or an error occurs and a diagnostic page is printed.
LAN HW Test
  caution:
Running this embedded test will erase your TCP/IP configuration.
This test performs an internal loopback test. An internal loopback test will send and receive packets only on the internal network hardware. There are no external transmissions on your network.
Select Yes to choose this test, or No to not choose it.
HTTP Test
This test checks operation of HTTP by retrieving predefined pages from the device, and tests the embedded Web server.
Select Yes to choose this test, or No to not choose it.
SNMP Test
This test checks operation of SNMP communications by accessing predefined SNMP objects on the device.
Select Yes to choose this test, or No to not choose it.
Data Path Test
This test helps to identify data path and corruption problems on an HP postscript level 3 emulation device. It sends a predefined PS file to the device, However, the test is paperless; the file will not print.
Select Yes to choose this test, or No to not choose it.
Select All Tests
Select this item to run all the embedded tests. Select Yes to run all tests, or select No to not run all tests.
Execution Time [H]
Use this item to specify the length of time (in hours) that an embedded test will be run. You can select a value from 1 to 60 hours. If you select zero (0), the test runs indefinitely until an error occurs or device is turned off.
Data gathered from the HTTP, SNMP, and Data Path tests is printed after the tests have completed.
Execute
No*: Do not initiate the selected tests.
Yes: Initiate the selected tests.
Ping Test
This test is used to check network communications. This test sends link-level packets to a remote network host, then waits for an appropriate response.
Dest Type
Specify whether the target device is an IPv4 or IPv6 node.
Dest IPV4
Type the IPv4 address.
Dest IPV6
Type the IPv6 address.
Packet Size
Specify the size of each packet, in bytes, to be sent to the remote host. The minimum is 64 (default) and the maximum is 2048.
Timeout
Specify the length of time, in seconds, to wait for a response from the remote host. The default is 1 and the maximum is 100.
Count
Specify the number of ping test packets to send for this test. Select a value from 1 to 100. To configure the test to run continuously, select 0.
Print Results
If the ping test was not set for continuous operation, you can choose to print the test results. Select Yes to print results. If you select No (default), results are not printed.
Execute
Specify whether to initiate the ping test. Select Yes to initiate the test, or No to not run the test.
Ping Results
Use this item to view the ping test status and results using the control panel display.
Packets Sent
Shows the number of packets (0 - 65535) sent to the remote host since the most recent test was initiated or completed.
Packets Received
Shows the number of packets (0 - 65535) received from the remote host since the most recent test was initiated or completed.
Percent Lost
Shows the percent of ping test packets that were sent with no response from the remote host since the most recent test was initiated or completed.
RTT Min
Shows the minimum detected roundtrip- time (RTT), from 0 to 4096 milliseconds, for packet transmission and response.
RTT Max
Shows the maximum detected roundtrip- time (RTT), from 0 to 4096 milliseconds, for packet transmission and response.
RTT Average
Shows the average round-trip-time (RTT), from 0 to 4096 milliseconds, for packet transmission and response.
Ping In Progress
Shows whether a ping test is in progress. Yes indicates a test in progress, and No indicates that a test completed or was not run.
Refresh
When viewing the ping test results, this item updates the ping test data with current results. Select Yes to update the data, or No to maintain the existing data. However, a refresh automatically occurs when the menu times out or you manually return to the main menu.
Link Speed
The link speed and communication mode of the print server must match the network. The available settings depend on the device and installed print server. Select one of the following link configuration settings:
  caution:
If you change the link setting, network communications with the print server and network device might be lost.
Auto*: The print server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.)
10T Half: 10 Mbps, half-duplex operation.
10T Full: 10 Mbps, Full-duplex operation.
100TX Half: 100 Mbps, half-duplex operation.
100TX Full: 100 Mbps, full-duplex operation.
100TX Auto: Limits auto-negotiation to a maximum link speed of 100 Mbps.
1000TX Full: 1000 Mbps, full-duplex operation.
Print Protocols
Use this item to print a page that lists the configuration of the following protocols: IPX/SPX, Novell NetWare, AppleTalk, DLC/LLC.

Fax Setup menu

note:
Use the fax setup wizard to configure fax options if the analog fax accessory is installed. If the analog fax accessory is not installed, the device can send faxes by using a LAN fax service or Internet fax service. Use the embedded Web server to configure those services. See Use the embedded Web server.
Fax Setup menu
Menu item
Sub-menu item
Sub-menu item
Values
Description
Fax Setup Wizard
Use this wizard to set up options for sending faxes if the analog fax accessory is installed.
For more information, see Initial fax setup.
Required Settings
Country/Region
Select a value from the list.
Use this item to change the required fax settings that have been setup using the Fax Setup Wizard.
Date/Time
Type a value.
Fax Header
Phone Number
Company Name
Type a value.
PC Fax Send
Enabled
Disabled*
Use this feature to enable or disable PC Fax Send. PC Fax Send enables users to send faxes through the device from their computers if they have the correct driver installed.
Fax Send Settings
Fax Dial Volume
Off
Low*
High
Use this feature to set the volume of the tones that you hear while the device dials the fax number.
Error Correction Mode
Enabled*
Disabled
When error-correction mode is enabled and an error occurs during fax transmission, the device sends or receives the error portion again.
JBIG Compression
Enabled
Disabled*
The JBIG compression reduces fax-transmission time, which can result in lower phone charges. However, using JBIG compression sometimes causes compatibility problems with older fax machines. If this occurs, turn off the JBIG compression.
Dialing Mode
Tone*
Pulse
Use this feature to specify either tone or pulse dialing for outgoing faxes.
Redial On Busy
The range is between 0 and 9. The factory default is 3 times.
Type the number of times the device should attempt to redial if the line is busy.
Redial On No Answer
Never
Once*
Twice
Use this feature to specify the number of times the device should attempt to dial if the recipient fax number does not answer.
Redial Interval
The range is between 1 and 5 minutes. The factory default is 5 minutes.
Use this feature to specify the number of minutes between dialing attempts if the recipient number is busy or not answering.
Detect Dial Tone
Enabled*
Disabled
Use this feature to specify whether the device should check for a dial tone before sending a fax.
Dialing Prefix
Off*
Custom
Use this feature to specify a prefix number that must be dialed when sending faxes from the device. Use a comma to indicate a required pause.
Billing Codes
Setup
Billing codes off*
Billing codes on
When billing codes are enabled, a prompt appears that asks the user to enter the billing code for an outgoing fax.
This prompt does not appear if Allow users to edit billing codes is not checked.
Minimum Length
The range is between 1 and 16 digits. The default is 1 digit.
Default Billing Code
Type a value.
Allow users to edit billing codes
Billing Code List
Fax Receive Settings
Rings To Answer
The factory default is 2 rings.
Use this feature to specify the number of rings that must occur before the fax modem answers.
Ring Interval
Select a value in the range.
Use this feature to control the time, in milliseconds, between rings for incoming faxes.
Ringer Volume
Off
Low
High
Set the volume of the ring tone for incoming faxes.
Blocked Fax Numbers
Add Blocked Numbers
Type the fax number to add to the list of blocked fax numbers, then touch the right arrow ( ) to add it to the list.
Use this feature to add or delete numbers from the blocked fax list. The blocked fax list can contain up to 30 numbers. When the device receives a call from one of the blocked fax numbers, it deletes the incoming fax. It also logs the blocked fax in the activity log.
Delete Blocked Numbers
Select a fax number to remove.
Delete All Blocked Numbers
Yes
No
Maximum Baud Rate
Select a value from the list.
Use this feature to set the maximum baud rate for receiving faxes. This can be used as a diagnostic tool for troubleshooting fax problems.

E-mail Setup menu

Use this menu to enable the e-mail feature and to configure basic e-mail settings. You can also configure these settings by using the embedded Web server.
note:
To configure advanced e-mail settings, use the embedded Web server. For more information, see Use the embedded Web server.
E-mail Setup menu
Menu item
Sub-menu item
Values
Description
E-mail Setup Wizard
Use this wizard to set up basic options for the E-mail feature.
For more information, see Initial e-mail setup.
SMTP Gateway
Host Name
Use this menu item to set the IP address of the SMTP Gateway that is used to send e-mail.
Set the Host Name to the address of the SMTP Gateway on the network.
Set the Port to the communication port used for sending e-mail using the SMTP server.
Port
25*
SMTP Server Authentication
Authentication Required
No*
Yes
Use this item to enable or disable user authentication to the SMTP Server.
User Name
Type a user name.
Password
Type a password.
Default From Adress
From E-mail Address
If a user does not sign in at the device before using the E-mail function, or no e-mail address is associated with the user account, the default e-mail address will be used.
Dispaly Name
Type an E-mail address.
This is the default e-mail address associated with e-mail sent from the device. If the user signs in at the control panel, their e-mail address replaces this address.
Lock Default Address
If this option is selected, the From address field cannot be altered by an e-mail program.

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Indonesia

hp-detect-load-my-device-portlet

Actions
Loading...