hp-support-head-portlet

動作
正在載入...
HP 顧客貼心服務 - 知識庫

hp-contact-secondary-navigation-portlet

動作
正在載入...

hp-share-print-widget-portlet

動作
正在載入...

hp-concentra-wrapper-portlet

動作
正在載入...

HP EliteBook 2530p Notebook PC - Removing and Replacing the Optical Drive

Introduction

This document is provided to assist in removing and replacing the Optical drive for the HP EliteBook 2530p Notebook PC.

Minimum skill level

The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.

Tools required

P1 Phillips-head screwdriver

Parts required

注意:
Part numbers are subject to change.
The replacement part number will vary depending on the Optical drive that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
DVD-ROM drive - SATA interface, 9.5 mm tray load
492558-001 (Modified)
Yes
DVD/RW and CD-RW Super Multi Double-Layer combination drive - SATA interface, 9.5 mm tray load
492559-001 (Modified)
Yes
注意:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Summary of instructions

To view a video demonstrating the procedure for removing the Optical drive, click on the link below. Or use the product video listing on the HP Services Media Library, then select Optical drive from the menu on the upper left hand side of the screen.
Click here to view the Optical drive removal video (right-click on the link to open in a new window/tab).

Optical drive removal

  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      敬告:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2. 注意:
    The optical drive is an option and will not be installed on some models. If an optical drive is not installed, an optical drive bay bezel with a third USB port will be located on the left side of the notebook.
  3. Loosen the captive P1 Phillips-head screw that secures the expansion memory/wireless LAN Minicard cover to the bottom of the notebook.
  4. Use your finger or a flat-bladed tool to lift the edge of the expansion memory/wireless LAN Minicard cover and remove it.
  5. Remove the 4 mm P1 Phillips-head screw that secures the optical drive inside the expansion memory/wireless LAN Minicard compartment.
  6. Remove the 4 mm P1 Phillips-head screw that secures the optical drive near the bottom front corner of the base enclosure.
  7. Use your finger to grasp the edge of the optical drive bezel and slide the optical drive out of the base enclosure.

Optical drive replacement

  1. Insert the optical drive into the base enclosure until the connector is seated.
  2. Replace the 4 mm P1 Phillips-head screw that secures the optical drive near the bottom front corner of the base enclosure.
  3. Replace the 4 mm P1 Phillips-head screw that secures the optical drive inside the expansion memory/wireless LAN Minicard compartment.
  4. Toe the expansion memory/wireless LAN Minicard cover into the base enclosure.
  5. Tighten the captive P1 Phillips-head screw.

Parts return


hp-feedback-input-portlet

動作
正在載入...

hp-feedback-banner-portlet

動作
正在載入...

hp-country-locator-portlet

動作
正在載入...
國家/地區: 中國香港

hp-detect-load-my-device-portlet

動作
正在載入...