solution Contentsolution Content

HP Color LaserJet Enterprise 5700, 5800, 6700, 6800, X557, X57945, X654, X677 - Removal and replacement: Solid state drive (SSD)

Learn about removing and replacing the solid state drive.

Install the SSD | HP Color LaserJet 5700/6700, X557/X654, MFP 5800/6800, X579/X677

Learn how to install the solid state drive (SSD) for the HP Color LaserJet 5700, X557, 6700, 6701, X654, MFP 5800, X57945, X58045, 6800, 6801, X677 printers.

Before performing service

Turn the printer power off

Disconnect the power cable.

Warning:
To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cord before attempting to service the printer.

If the part is damaged and cannot be cleaned, use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.

Part information
Part number	Part description
1M0Q4A	HP LaserJet Secure Solid State Drive

Required tools

#2 Phillips screwdriver with a magnetic tip and a 152 mm 6 in shaft length

After performing service

Turn the printer power on

Connect the power cable.
Use the power switch to turn the power on.

Post service test

Print any pages necessary to make sure the printer is functioning correctly.

Remove the formatter cover

Follow these steps to remove the formatter cover.

Remove one screw (callout 1), and then slide the formatter cover (callout 2) away from the printer to remove it.

Tip:
Reverse the removal steps to install the assembly.

Remove the formatter cover

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

Dispose of the defective part.

Note:
HP recommends responsible disposal of the part.

http://www8.hp.com/us/en/hp-information/environment/product-recycling.html
Unpack the replacement part from the packaging.

Important:
Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

Install the SSD card only

Learn how to install the SSD card.

CAUTION:

ESD sensitive part.

Place one end of the riser PCA into the cradle, and then press the other end of the card into the cradle.

Install PCA in cradle
Verify that the PCA is properly installed by listening for a click when it is pressed into place. Also verify that the PCA is underneath the two indicated tabs at the end.

Verify PCA installation
Position the PCA cradle on the bracket.

Position the PCA cradle
Close two clips at the end of the bracket to secure the PCA cradle.

Close the clips
Install the support cross member onto the bracket.

Install the cross member
Align the SSD card with the connector on the PCA. Note how the end of the SSD is keyed so that it can be installed one way only.

Align the SSD card
Seat the SSD in the PCA connector, and then snap the other end of the SSD on the cross member.

Secure the SSD on the cross member
Align the bracket assembly with the formatter connector.

Align the bracket assembly
Press the bracket assembly to firmly seat it in the formatter connector.

Install the bracket assembly
Install two pins to secure the bracket assembly to the formatter faceplate.

Install two pins

Install the SSD card with the HDD

Learn how to install the SSD card with an HDD.

CAUTION:

ESD sensitive part.

Release two pins from the formatter faceplate.

Release two pins
Remove the HDD assembly

Remove the HDD
Open two clips on the HDD bracket.

Open two clips
Remove the PCA cradle from the HDD bracket.

Remove the PCA cradle
Release one tab (callout 1), raise the end of the PCA up and off the cradle (callout 2), and then remove the PCA from the cradle (callout 3).

Remove the PCA from the holder
Place one end of the new PCA on the cradle (callout 1), and then rotate the other end down onto the cradle (callout 2). Make sure to orientate the PCA on the cradle as shown. Push down on the PCA to install it on the cradle (an audible click is heard when it snaps into place).

Note:
Make sure that the PCA is firmly seated under the clips on the cradle.

Install the PCA in the cradle
Align the PCA cradle with the bracket.

Align the PCA cradle
Close two clips to secure the PCA cradle to the bracket.

Close two clips
Install the support cross member onto the bracket.

Install the support cross member
Align the SSD card with the PCA connector. Note how the end of the SSD is keyed so that it can be installed one way only.

Align the SSD card
Seat the SSD in the PCA connector, and then snap the other end of the SSD on the cross member.

Secure the SSD on the cross member
Align the bracket assembly with the formatter connector.

Align the bracket assembly
Press the bracket assembly to firmly seat it in the formatter connector.

Install the bracket assembly
Install two pins to secure the bracket assembly to the formatter faceplate.

Install two pins

Install the SSD card with USB

Learn how to install the SSD card with a USB card.

CAUTION:

ESD sensitive part.

Remove the USB PCA from the formatter connector.

Remove the USB PCA
Install the SSD card on the board.

Install the SSD card
Position the PCA cradle on the bracket.

Position the PCA cradle
Close two clips to secure the PCA cradle to the bracket.

Close two clips
Insert the board into the PCA connector.

Insert the board
Secure the board to the bracket (an audible click is heard when it snaps into place).

Secure the board to the bracket
Align the bracket assembly with the formatter connector, and then press the bracket assembly to firmly seat it in the formatter connector.

Install the bracket assembly
Install two pins to secure the bracket assembly to the formatter faceplate.

Install two pins