hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP Color LaserJet Enterprise M652, M653, Managed E65050, E65060, E65150, E65160 and HP Color LaserJet Enterprise MFP M681, M682, Managed MFP E67550, E67560, E67650, E67660 - Removal and replacement: Intermediate transfer belt (ITB)

This document provides the procedures to remove and replace the intermediate transfer belt (ITB).

Mean time to repair: 5 minutes

Service level: Basic

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part number

Part description

P1B93-67901

Intermediate transfer belt

Required tools

  • No special tools are needed to remove or install this assembly.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Print a page and verify that the print quality is acceptable.

Remove the intermediate transfer belt (ITB)

Follow these steps to remove the intermediate transfer belt (ITB).

  1. Open the right door.

    Open the right door

    Open the right door
  2. Release the blue latch (callout 1), and then lower the transfer assembly (callout 2).

    Lower the transfer assembly

    Lower the transfer assembly
  3. Grasp the two blue handles on the ITB.

    Grasp the two blue handles

    Grasp the two blue handles
  4. Pull the ITB partially out of the printer.

    Pull the ITB partially out of the printer

    Pull the ITB partially out of the printer
  5. Grasp the outside edges of the ITB to support it, and then remove the ITB from the printer.

    Remove the ITB

    Remove the ITB

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the ITB

Follow these steps to install the ITB.

  1. Remove the ITB from the packaging, and then remove the protective film around the ITB.

    Remove the protective film

    Remove the protective film
  2. Handle the replacement ITB by the orange handles. Do not touch the grey-plastic belt. Skin oils and fingerprints on the belt can cause print-quality problems.

    Remove all packing materials

    Remove all packing materials
  3. Align the ITB with guides inside the printer, and then carefully push it into the printer until the orange handles stop it.

    Align the ITB

    Align the ITB
  4. Remove the orange handle. Repeat this step for the remaining orange handle.

    Tip:

    HP recommends recycling the plastic handles.

    Remove the orange handles

    Remove the orange handles
  5. Using the blue handles, continue to carefully push the ITB into the printer.

    Push the ITB into the printer

    Push the ITB into the printer
  6. Continue to push the ITB into the printer until you hear a click, confirming it is fully installed.

    Make sure the ITB clicks into place

    Make sure the ITB clicks into place
  7. Close the right door.

    Close the right door

    Close the right door

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Hong Kong SAR

hp-detect-load-my-device-portlet

Actions
Loading...