hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet Enterprise MFP M631-M633, M634-M636 HP LaserJet Managed MFP E62555-E62575, E62655-E62675 - Removal and replacement: Fuser

This document provides the procedures to remove and replace the fuser.

Mean time to repair: 5 minutes

Service level: Basic

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part number

Part description

RM2-1256-020cn

Fuser Kit 110v

RM2-1257-020cn

Fuser Kit 220v

Required tools

  • No special tools are needed to remove or install this assembly.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Send a print job to the printer requiring stapling and collation to verify that the stapler/stacker correctly functions.

Remove the fuser

Follow these steps to remove the fuser.

  1. Do one of the following to locate the fuser:

    • M607/M608/M609/E60055/E60065/E60075/E60155/E60165/E60175 printers: Open the rear door.

    • M631/M632/M633/E62555/E65565/E62575/E62655/E62665/E62675 printers: Open the right door.

      Warning:

      The fuser might be hot. Always wait for the fuser to cool before removing.

    Open the rear door or open the right door

    Open the rear door or open the right door
  2. Hold the handles of the fuser and pull it out of the printer to remove it.

    Note:

    The image shown is for the M631/M632/M633/E62555/E65565/E62575/E62655/E62665/ E62675 printers, however the removal process is the same for M607/M608/M609/E60055/E60065/ E60075/E60155/E60165/E60175 printers after you have located the fuser in step 1.

    Remove the fuser

    Remove the fuser

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the fuser

Follow these steps to install the fuser.

  1. Hold the handles of the fuser and install it into the printer in the direction indicated by the arrow.

    Note:

    The image shown is for the M631/M632/M633/E62555/E65565/E62575/E62655/E62665/ E62675 printers, however the install process is the same for M607/M608/M609/E60055/E60065/E60075/ E60155/E60165/E60175 printers after you have located the fuser install location.

    Install the fuser

    Install the fuser
  2. Do one of the following:

    • M607/M608/M609/E60055/E60065/E60075/E60155/E60165/E60175 printers: Close the rear door.

    • M631/M632/M633/E62555/E65565/E62575/E62655/E62665/E62675 printers: Close the right door.

    Close the rear door or close the right door

    Close the rear door or close the right door

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Hong Kong SAR

hp-detect-load-my-device-portlet

Actions
Loading...