hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet Enterprise M607, M608, M609, M610, M611, M612, M612; HP LaserJet Managed E60055, E60065, E60075, E60155, E60165, E60175 - Removal and replacement: Internal USB ports/AA module

This document provides the procedures to install the internal USB ports/AA module.

Mean time to repair: 5 minutes

Service level: Basic

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part number

Part description

B5L28-67902

Two internal USB ports kit

Required tools

  • No special tools are needed to remove or install this assembly.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

No post service test is available for this assembly.

Remove the formatter cover

Follow these steps to remove the formatter cover.

  1. To remove the formatter cover, do the following:

    Note:

    A SFP printer is shown in this section. However, the procedure is correct for all printer models.

    • On the formatter cover, release two thumb screws (callout 1).

    • Slide the formatter cover in the direction indicated by the arrow (callout 2) and remove it.

    Release two thumb screws and remove the formatter cover

    Release two thumb screws and remove the formatter cover

Install the USB ports/AA module

Follow these steps to install the USB ports/AA module.

  1. From the internal USB ports/AA module accessory kit, obtain the following items:

    • The small PCA board.

    • The PCA mounting cradle.

    • The double-cable (B5L24–60106).

    Accesory kit items that are required

    Accesory kit items that are required
  2. Locate the empty space in the upper right corner where the internal USB ports/AA module will be installed.

    Locate the space for installing the internal USB ports/AA module

    Locate the space for installing the internal USB ports/AA module
  3. Do the following:

    • Hold the small PCA and the PCA mounting cradle in the correct orientation.

    • Align the top and bottom cutouts of the PCA on the tabs of the PCA mounting cradle.

    • Secure the small PCA on the PCA mounting cradle until it snaps in place.

    Mount the PCA on the PCA mounting cradle and snap it in place

    Mount the PCA on the PCA mounting cradle and snap it in place
  4. Attach the large white connector end of the double cable to the large connector receptacle on the small PCA board.

    Attach the large white connector to the PCA

    Attach the large white connector to the PCA
  5. Do the following:

    • Hold the small PCA attached to the PCA mounting cradle in the correct orientation, with the attached cable at the bottom.

    • In the upper right corner of the formatter cage area, locate the upper and lower sheet metal hooks.

    • Slide the assembly and mount it so that the upper and lower tabs of the PCA mounting cradle slide into the sheet metal hooks.

    Mount the assembly on the sheet metal hooks

    Mount the assembly on the sheet metal hooks
  6. On the formatter, disconnect the USB cable indicated by the arrow.

    Disconnect one formatter USB cable

    Disconnect one formatter USB cable
  7. Connect the USB cable (disconnected from the formatter) to the USB connector on the small PCA as indicated by the arrows.

    Note:

    The USB connector on the small PCA is to the left of where the white connector of the double-cable is installed.

    Connect the formatter USB cable to the small PCA

    Connect the formatter USB cable to the small PCA
  8. Connect the USB cable of the double-cable attached to the small PCA, to the USB connector on the formatter as indicated by the arrow.

    Connect the small PCA USB cable to the formatter USB connector

    Connect the small PCA USB cable to the formatter USB connector
  9. Connect the small white connector of the double-cable attached to the small PCA, to the matching connector near the upper right edge of the formatter as indicated by the arrow.

    Connect the small white connector from the small PCA to the formatter

    Connect the small white connector from the small PCA to the formatter

Install the formatter cover

Follow these steps to install the formatter cover.

  1. Slide the formatter cover onto the printer in the direction indicated by the arrow (callout 1), and then tighten two thumb screws (callout 2).

    Note: An MFP printer is shown in this section. However, the procedure is correct for all printer models.

    Slide on the formatter cover and tighten two thumb screws

    Slide on the formatter cover and tighten two thumb screws

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag United Kingdom

hp-detect-load-my-device-portlet

Actions
Loading...