Error:

Javascript est désactivé dans ce navigateur. Javascript est requis pour cette page. Modifiez les paramètres de votre navigateur pour autoriser l'exécution de Javascript. Pour des instructions spécifiques, voir la documentation de votre navigateur.

hp-support-head-portlet

Actions

Chargement...

Assistance clientèle HP - Base de connaissances

hp-contact-secondary-navigation-portlet

Actions

Chargement...

hp-share-print-widget-portlet

Actions

Chargement...

Information

Avez-vous besoin d'aide avec Windows 11 ?
Vérifiez les informations sur la compatibilité, la mise à niveau et les correctifs disponibles auprès de HP et de Microsoft. Centre d'assistance Windows 11

Information

Problèmes de son ou de l’audio ? Essayez notre outil automatisé, HP Audio check!

Avis

hp-concentra-wrapper-portlet

Actions

Chargement...

HP Officejet 5600 All-in-One Printer Series- Setting up the All-in-One (Hardware)

Introduction

This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.

This document includes the following steps to set up the product:

Unpack the All-in-One
Check the contents of the box
Attach the control panel faceplate
Attach the trays and load paper
Connect the power cord and adapter
Connect the supplied phone cord
Select the language/region
Install the cartridges
Align the cartridges

Setting up the All-in-One

Follow these steps in order.

Step one: Unpack the All-in-One

Remove all tape and cardboard packing material from the outside and inside of the product.

Figure : Remove all packing materials

Step two: Check the contents of the box

The contents might vary by country/region. See the packaging for a list of items shipped in the box.

Step three: Attach the control panel faceplate

The control panel faceplate must be in place for the product to work. If the control panel faceplate is not already attached, do the following:

Align the faceplate over the buttons on the top of the product.

Figure : Align the faceplate
Snap the faceplate firmly into place.

Step four: Attach the trays and load paper

Insert the tabs of the bottom tray into the product, and then lower the tray until it is flat.

Figure : Insert the bottom tray
Slide the paper adjuster to the left.

Figure : Slide the paper adjuster to the left
Insert plain white paper.

Figure : Load plain paper
Insert the top edge of the output tray into the light gray latches, and then lower it.

Figure : Attach the output tray
Open the paper tray extender.

Figure : Open the tray extender

Step five: Connect the power cord and adapter

Plug the printer end of the power adapter into the back of the product.
Plug the adapter end of the power cord into the power adapter.
Plug the remaining end of the power cord into a grounded wall outlet or surge protector.

Figure : Connect the power cord and adapter

Step six: Connect the supplied phone cord

Connect one end of the supplied phone cord to the phone port on the left (1-LINE) and the other to a wall jack.

Figure : Connect the phone cord
On the HP All-in-One control panel, press the On button ().

The green light flashes, and then becomes solid. This might take up to a minute.

Step seven: Select the language/region

When prompted, use the arrow keys to select your language, press OK, and then confirm.
When prompted, use the arrow keys to select your country/region, press OK, and then confirm.

Step eight: Install the cartridges

Lower the access door, and then wait for the carriage that holds the cartridges to move to the right side.

Figure : Lower the access door

Figure : The carriage
Pull the pink tab to remove the tape from both cartridges.
Figure : Remove the tape

Copper-colored contacts

Plastic tape with pink pull tab (must be removed before installing)

Ink nozzles under tape
Attention :
Do not touch the copper-colored contacts or ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.

Figure : Do not touch the electrical contacts or ink nozzles
Slide each new cartridge forward into its empty slot, and then gently push on the upper part of the cartridge until it snaps into place.
- Insert the tri-color cartridge into the left slot.
- Insert the black or photo cartridge into the right slot.
Figure : Insert the cartridges
Close the access door.

Figure : Close the access door

Step nine: Align the cartridges

After you insert the cartridges, a message displays indicating that the product is ready for alignment.

Align the cartridges when prompted from the printer control panel
The printer prompts you to align the cartridges each time you install or replace a cartridge.

Remarque :
If you remove and reinstall the same cartridge, the printer will not prompt you to realign the cartridge. The alignment values for the cartridge are recorded in the printer from the first alignment.
1. Make sure that you have letter or A4 unused plain, white paper loaded in the input tray, and then press OK.
  
  Remarque :
  If you have colored paper loaded in the input tray when you align the cartridges, the alignment fails. Load unused plain, white paper into the input tray, and then try the alignment again by restarting it from the control panel.
2. Wait for the alignment page to print, and then examine the page. The alignment page should have black and blue print areas, and the print areas should be sharp and clear, with no fading or streaking.
  
  Figure : Example of an alignment page
3. Lift the lid, place the top of the alignment page face-down on the left front corner of the scanner glass, and then close the lid.
  
  Figure : Place the alignment page on the scanner glass
4. Press OK to begin the alignment. The printer aligns the cartridges. After the On light stops blinking, a message displays to indicate that the alignment is complete.
5. Recycle or discard the alignment page.
Align the cartridges at any time from the printer control panel
Follow these steps to start alignment at any time from the printer control panel.
1. Make sure that you have letter or A4 unused plain, white paper loaded in the input tray.
  
  Remarque :
  If you have colored paper loaded in the input tray when you align the cartridges, the alignment fails. Load unused plain, white paper into the input tray, and then try the alignment again.
2. Press Setup.
3. Press 6 to select Tools, and then press 2 to select Align Print Cartridge.
4. Wait for the alignment page to print, and then examine the page. The alignment page should have black and blue print areas, and the print areas should be sharp and clear, with no fading or streaking.
  
  Figure : Example of an alignment page
5. Lift the lid, place the top of the alignment page face-down on the left front corner of the scanner glass, and then close the lid.
  
  Figure : Place the alignment page on the scanner glass
6. Press OK to begin the alignment. The printer aligns the cartridges. After the On light stops blinking, a message displays to indicate that the alignment is complete.
7. Recycle or discard the alignment page.