hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...

hp-concentra-wrapper-portlet

Actions
Loading...

HP Designjet 1000 Series Printers - Setup Instructions

Printer components
Ensure the following components are in the shipping container, stand assembly box, and end packing pieces:
Quantity
Component
2
Screw Drivers
18
Screws
12
Media-Bin Retaining Clips
6
Media-Bin Arms
2
Media-Bin Capping Strips
1
Media-Bin Support
2
Feet
2
Legs
1
Base Tray
1
Cross Brace
3
Media Guides
1
Front Panel Overlay
1
Printer Body
1
Assembly Instruction Booklet
Unpacking the components
  note:
To move the Shipping Container, use the eight handles provided on the box. Four or more people should perform this procedure.
  1. Before unpacking the printer, ensure at least 3 meters (9 feet) of space is available in front of the shipping container.
  2. Remove the two packing straps and plastic handles from both sides of the container.
    Figure : Removing straps and plastic handles
  3. Remove the Outer Sleeve from the container, then remove the end packing pieces, accessory boxes, and stand box.
    Figure : Removing outer sleeve
      Figure : Removing accessory boxes and stand box
    1. Accessory boxes
    2. Stand box
  4. Remove the plastic handles from both sides of the container.
    Figure : Removing plastic handles
  5. Remove the inner sleeve from the container, then the two packing pieces.
    Figure : Removing inner sleeve and packing pieces
    Figure : Removing the packing pieces
  6. Remove the base tray and the protective plastic covering.
    Figure : Removing base tray
      note:
    The bas tray appearance may differ from the illustration.
  7. Unpack the stand components from the stand box.
      Figure : Stand components
    1. Anti-slip material
      caution:
    Do not remove the anti-slip material from the feet.
Assemble the printer stand
  note:
Assemble all the Stand Components on a flat surface.
  1. Attach the legs to the cross brace.
    Figure : Attaching legs to cross brace
  2. Attach the media-bin support to the legs with four screws (two people should perform this step).
      Figure : Attaching the media-bin support
    1. Media-bin support
  3. Install four screws into the legs (two screws into each leg).
    Figure : Leg screw installation
  4. Carefully clip the feet onto the base tray.
      Figure : Clipping the feet onto the base tray
    1. Correct curvature of the base tray
  5. Position the feet onto the leg assembly, and secure the feet to the legs with 6 screws.
      Figure : Correct feet positioning
    1. Anti-slip material
      caution:
    Do not remove the anti-slip material.
    Figure : Securing the feet to the legs
  6. Some screws may have come loose during assembly (verify all screws are fully tightened).
    Figure : Re-tightening screws
Unpack the printer
  1. Remove the end packing supplements.
      Figure : Removing the packing supplements
    1. Packing supplements
  2. Pull down the two flaps on the side of the container (with the corrugated edges).
      Figure : Pulling down the flaps
    1. Perforations
  3. Slide the printer to the side of the container with the flaps turned down, and carefully roll the printer out.
      warning:
    The printer is heavy and requires two people to perform this step.
    Figure : Rolling printer
    Figure : Correct positioning of printer form following removal from crate
  4. Gently pull aside the protective plastic covering, put the stand assembly onto the printer, then secure it with four screws.
      Figure : Securing the printer to the stand
    1. Pull aside plastic covering
    2. Orientation of the Media-bin support and arrow
      warning:
    The printer is heavy and requires two people to perform the next step.
  5. Carefully lay the printer on its side, and then lift the printer into the upright position (two people should perform this step).
    Figure : Laying the printer on its side
    Figure : Standing the print up
  6. Remove the end packing and the plastic covering from the printer.
    Figure : Removing the end packing and the plastic covering
  7. Tear off the anti-slip material from the wheels (the printer does not need to be lifted to perform this step).
    Figure : Removing the anti-slip material
  8. Remove the two packing straps and the silicon bag, then remove the protective covering from the printer window.
      Figure : Removing packing straps and silicon bag
    1. Packing strip
    2. Desiccant bag
    Figure : Removing plastic covering from top cover window
  9. Open the window and remove the Carriage packing piece.
    Figure : Removing the carriage packing
  10. Remove the two white arrows (pull the arrow towards you, and remove it from the printer).
    Figure : Removing the white arrows
Assemble the printer
  note:
Steps 1 and 2 below are for the Designjet 1000 series "A" models only (C6074A, C6075A). Continue with Step 3 if the printer is a "B" model (C6074B, C6075B).
  1. Unpack the three media guides (removed earlier from the end packing pieces).
  2. Snap the media guides into position on the back of the printer.
      Figure : Snapping the media guides into position
    1. Back of printer
  3. From the back of the printer insert the six media-bin arms, and secure the arms to the cross brace with six retaining clips.
    Figure : Inserting the media-bin arms
    Figure : Securing media-bin arm with retaining clip
  4. Secure the arms to the media-bin support with six retaining clips.
    Figure : Securing the arms to the media-bin support
  5. Push together the media-bin capping strips (2), enclosing the media-bin arms.
    Figure : Attaching the media-bin capping strips
  6. Attach the front panel overlay to the front panel. Ensure that the cutouts on the overlay are correctly positioned on the front panel locating tabs.
      Figure : Attaching the front panel overlay
    1. Locating tab
    2. Cutouts
  7. Remove the two media rolls from the shipping container.
    Figure : Removing the two media rolls
  8. The printer is now assembled.
    Figure : Assembled printer

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Middle East

hp-detect-load-my-device-portlet

Actions
Loading...