hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet Enterprise MFP M725 - Removal and replacement: Formatter PCA

This document provides the procedures to remove and replace the formatter PCA.

Mean time to repair: 10 minutes

Service level: Basic

Before performing service

Turn the printer power off.

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.

Part information

Formatter assembly kit

CF066-67901

Replacement formatter assembly kit

CF066-67903

Replacement formatter assembly kit— China

Required tools

  • No tools are required to remove the formatter PCA.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Make sure that the printer initializes to a Ready state.

Print a configuration page to make sure that the printer is functioning correctly.

Remove the Formatter PCA

Follow these steps to remove the Formatter PCA.

The formatter is located in the right rear corner of the product. You do not need tools to remove it.

CAUTION:

ESD sensitive assembly.

  1. Locate the formatter and turn the two thumb-screws (callout 1) counterclockwise to detach the formatter base plate from the chassis.

    Remove the formatter (1 of 2)

    Remove the formatter (1 of 2)
  2. Pull the formatter away from the product to remove it.

    Remove the formatter (2 of 2)

    Remove the formatter (2 of 2)

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Replace the Formatter PCA

Follow these steps to replace the Formatter PCA.

The formatter is located in the right rear corner of the product. You do not need tools to replace it.

CAUTION:

ESD sensitive assembly.

  1. Push the formatter into the product.

    Replace the formatter (1 of 2)

    Replace the formatter (1 of 2)
  2. Locate the formatter and turn the two thumb-screws (callout 1) clockwise to attach the formatter base plate to the chassis.

    Replace the formatter (2 of 2)

    Replace the formatter (2 of 2)

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Africa

hp-detect-load-my-device-portlet

Actions
Loading...