hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet Enterprise MFP M631, M632, M633, M634, M635, M636; HP LaserJet Managed MFP E62555, E62565, E62575, E62655, E62665, E62675 - Removal and replacement: White backing and retention clips

This document provides the procedures to remove and replace the white backing and retention clips.

Mean time to repair: 5 minutes

Service level: Basic

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Before performing service

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cable before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts

Part information

Part numbers

Part description

5851-7206

White backing and retention clips A4 kit

5851-7207

White backing retention clips (only) kit

Required tools

  • No special tools are needed to remove or install this assembly.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Print a page and make sure that the toner is fused to the page properly.

Remove the white backing and retention clips

Follow these steps to remove the white backing and retention clips.

  1. Open the document feeder.

    Open the document feeder

    Open the document feeder
  2. Grasp the edge of the white backing, and then firmly pull it away from the document feeder to remove the white backing and the retention clips.

    Note:

    The clips are still attached to the white backing when it is removed.

    Remove the white backing

    Remove the white backing

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Install the white backing and retention clips

Follow these steps to install the white backing and retention clips.

  1. Verify that the springs are positioned correctly on each of the retention clips provided in the replacement kit.

    Verify spring positions

    Verify spring positions
  2. In the location where the white backing was removed, install seven retention clips in the document feeder. Align the tabs on the clip with the slots in the document feeder.

    Install seven retention clips

    Install seven retention clips
  3. Press on each retention clip to make sure that they are fully installed. You will hear an audible click when the clip is correctly installed.

    Press on each clip

    Press on each clip
  4. Peel an adhesive square off of the backing sheet.

    Remove an adhesive square

    Remove an adhesive square
  5. Attach an adhesive square to each retention clip on the document feeder.

    Note:

    Do not remove the protective film off of the top of the adhesive square yet.

    Attach the adhesive squares on each retention clip

    Attach the adhesive squares on each retention clip
  6. Remove the protective film off of each adhesive square.

    Remove the protective film

    Remove the protective film
  7. Position the white backing on the image scanner glass. Make sure that the corner with the embossed arrow on the backing is positioned against the corner with the white arrow on the scanner.

    Position the white backing

    Position the white backing
  8. Close the document feeder.

    Close the document feeder

    Close the document feeder
  9. Open the document feeder.

    Open the document feeder

    Open the document feeder
  10. Press on the white backing at the location of each retention clip to ensure that the backing is securely attached to the adhesive on the clips.

    Press on the white backing

    Press on the white backing
  11. Close the document feeder.

    Close the document feeder

    Close the document feeder

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Africa

hp-detect-load-my-device-portlet

Actions
Loading...