hp-support-head-portlet

Actions
Loading...

Welcome to HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...

hp-concentra-wrapper-portlet

Actions
Loading...

HP Compaq nc4010 Notebook PC - Removing and Replacing the Wireless LAN Mini PCI Card

Introduction
This document is provided to assist in removing and replacing the wireless LAN mini PCI card for the HP Compaq nc4010 Notebook PC.
Minimum skill level
The End User requires no hardware-specific training to replace the defective part. The End user should have familiarity with system hardware and software requiring repair.
Tools required
  • Small, Phillips-head (P0 and P1) screwdriver
  • TR7 screwdriver
Parts required
  note:
Part numbers are subject to change.
The replacement part number will vary depending on the wireless LAN mini PCI card that is being replaced. If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. Click here for more information on returning parts to HP.
Description
Part Number
Requires Return
HP W500 Mini PCI wireless module 802.11a/b/g - Wi-Fi certified, 2.4 and 5 Ghz frequency - Maximum data rate of up to 11 Mb/s
325525-001 (Original)
Yes
Mini PCI 802.11b/g wireless LAN (WLAN) card - Supports IEEE 802.11b/g wireless standards, including Advanced Encryption Standard (AES) support - Maximum data rate of up to 54 Mb/s
325526-001 (Original)
Yes
Bluetooth wireless device - USB, 2S (embedded) - Supports Bluetooth v1.1 specifications
333605-001 (Original)
Yes
Mini PCI IEEE 802.11b (Wi-Fi) wireless networking card (Worldwide, rest-of-world)
345640-001 (Original)
Yes
Mini-PCI 802.11b/g wireless networking card (Worldwide, most-of-world)
368247-001 (Original)
Yes
Mini-PCI 802.11b/g wireless networking card (Worldwide, rest-of-world)
368248-001 (Original)
Yes
  note:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.
Summary of instructions
To view a video demonstrating the procedure for removing the wireless LAN mini PCI card, click on the link below. Or use the product video listing on the HP Services Media Library (Click here to go to HP Service Media Library), then select Wireless LAN Mini PCI Card from the menu on the upper left hand side of the screen.
Click here to view the wireless LAN mini PCI card removal video (right-click on the link to open in a new window/tab).
Wireless LAN mini PCI card removal
  1. Review the safety considerations before performing the steps listed below by clicking on the following link:
      caution:
    Failure to comply with the precautions could result in damage to your product or loss of data.
  2.   note:
    The Mini PCI cover can be secured with either a captive P0 Phillips-head screw or a captive TR7 tamper resistant screw that requires a special TR7 screwdriver.
  3. Loosen the captive screw that secures the Mini PCI cover to the bottom of the notebook.
  4. Use your finger to lift the outside edge of the Mini PCI cover and remove it.
  5. Carefully disconnect the two wireless antenna cables from the Mini PCI card with a small needlenose pliers or tweezers.
      note:
    Use care when disconnecting the wireless antenna cables from the Mini PCI card. Damaged cables or connectors can degrade notebook performance.
  6. Push both arms outward simultaneously to release the Mini PCI card to the spring tension position.
  7. Grasp the Mini PCI card by the edges and pull gently to remove it.
  8. Place the Mini PCI card in a static dissipative bag.
Wireless LAN mini PCI card replacement
  1. Remove the Mini PCI card from the static dissipative bag.
  2. Locate the alignment slot and align it to the board receptacle.
  3. Grasp the Mini PCI card by the edges and push gently to replace it.
  4. Press the Mini PCI card down to latch the arms.
  5. Reconnect the two wireless antenna cables to the Mini PCI card.
      note:
    Use care when connecting the wireless antenna cables to the Mini PCI card. Damaged cables or connectors can degrade notebook performance.
  6. Toe the Mini PCI cover into the enclosure.
  7. Tighten the captive screw.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country: Africa

hp-detect-load-my-device-portlet

Actions
Loading...