Error:

Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions.

hp-support-head-portlet

Actions

HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions

hp-share-print-widget-portlet

Actions

Information

Fix Windows 10 Update Issues
> Print spooler or any other printer problems caused by a Windows 10 update or upgrade - Click Here
> Resolve Windows 10 or update issues on HP computer – Click Here

hp-concentra-wrapper-portlet

Actions

HP Smart Tank 450 Printers - Wireless Printer Setup (Mac)

This document is for Mac computers and the HP Smart Tank Wireless 450, 455, and 457 printers.

To set up your HP printer on a wireless (Wi-Fi) network, restore the printer wireless settings to the factory defaults, install the print driver and software, and then set up the wireless connection.

Step 1: Prepare for installation

Before installing the printer software and connecting to your wireless network, check the requirements, turn on the computer and the router, and set up the printer.

To use your printer on a wireless network, you need the following items:
- A computer connected to your wireless network
- Internet access: HP recommends broadband Internet access such as cable or DSL for software downloads, using Web Services, and getting printer updates.
Make sure the router and computer are turned on, and that the computer is connected to the same wireless network to which you want to connect the printer.
Set up the printer, load paper into the input tray, and install the ink cartridges. For more information about setting up the printer, go to First Time Printer Setup.
Turn on the printer and place it close to the computer and within range of the router during the setup procedure.
Disconnect any USB cables from the printer, if necessary.

Step 2: Restore default wireless settings on the printer

Reset the wireless settings on the printer so the connection completes successfully.

On the printer control panel, make sure the wireless light is blinking and the Power button light is bright. If the light is not bright, press the Power button to wake the printer from sleep mode.
If the wireless light is not blinking, press and hold the Wireless button and the Cancel button at the same time for 3 seconds.

The wireless light blinks. Repeat these steps if the wireless light does not blink.
Immediately continue to the next step to install the software. You have approximately 120 minutes to complete the software setup using the HP auto wireless connect feature.

Step 3: Install the software and print driver

On the computer you want to print from, start the HP print driver and software installation.

Go to 123.hp.com/ST450, and then click Download.
Open the Downloads folder on the Mac dock, and then click the HP Easy Start file to begin the installation.
Follow the on-screen instructions to complete the software installation.
- If HP Easy Start finds multiple printers, select the printer you want to install, and then continue with the on-screen instructions.
- If HP Easy Start does not find your printer, follow the on-screen instructions to connect your printer to the network.
  
  If the installer still does not find your printer, go to Printer Not Found During Network Driver Setup (Mac).
Return to the 123.hp.com page in your web browser to complete the printer registration and activation.

Frequently asked questions (FAQs)

Review these frequently asked questions about setting up the wireless network connection.

What if the printer connection drops or I change my network password?

There are a wide variety of Wi-Fi and router configurations for home networks. Some network settings and behaviors might cause the wireless connection to drop. To help keep the printer connected, you can manually set the printer IP address using the Embedded Web Server (EWS).

Restart the printer and the computer.
Make sure the Power button light is bright. If the light is not bright, press the Power button to wake the printer from sleep mode.
Try to print. If the issue persists, continue with these steps.
On the printer control panel, press the Wireless button and the Information button at the same time.

A Network Configuration Page prints.
Find the IP address on the page.

Figure : IP address on the Network Configuration Page
If the page does not list an IP address, the printer and the router are not connected. Use one of the following methods to connect and find the printer IP address.
- Router
  
  Sign in to your router configuration or setup page and find the printer IP address listed in an attached devices or DHCP Clients section.
- WPS
  
  Touch and hold the Wireless button on the printer until the Wireless light blinks, and then press the WPS button on your router. Wait for the wireless light to stop blinking and remain solid, print another Network Configuration Page, and then find the IP address.
- Wi-Fi Direct
  
  To turn on Wi-Fi Direct, press the Wi-Fi Direct button . Open the list of available networks on the computer, and then connect the computer to HP-Print-xx-[your printer model name]. Once connected, the printer IP address is 192.168.223.1.
Click the Apple menu, and then click System Preferences.
Click Print & Scan or Printers & Scanners.

Figure : Example of the Printers & Scanners window
Click the name of your printer, and then click Options & Supplies.
Click the General tab, and then click Show Printer Webpage....

The EWS opens.
Click the Network tab, click Wireless (802.11) from the left side of the window, and then click Network Address (IPv4).
Select Manual IP, and then click Suggest a Manual IP Address.

Figure : The IP Address Configuration window
Click Apply, and then restart the printer.

The printer remains connected to your network.

What if I cannot download the file from 123.hp.com?

If you cannot download files from 123.hp.com, go to HP Software & Driver Downloads to download and install the printer software.

Can I connect wirelessly using a temporary USB connection?

Yes, you can temporarily connect the printer to the Mac computer with a USB cable and then change the connection to wireless in the HP Utility software.

Connect a USB cable to the USB port on the rear of the printer and to the computer.
Click the Apple menu, and then click System Preferences.
Click Print & Scan or Printers & Scanners.

Figure : Example of the Printers & Scanners window
Click the plus sign , and then click Add Printer or Scanner.
Click the name of your printer with USB under Kind.
On the Use menu, select the name of your printer, and then click Add.
Click the name of your printer, and then click Options & Supplies.
Click Utility, and then click Open Printer Utility.

Figure : Opening Printer Utility
In HP Utility, click Wireless Setup.

Figure : Wireless Setup in HP Utility
Make sure your network displays on the Confirm Wireless Settings window, and then click Continue to complete the wireless configuration.

Figure : Confirm Wireless Settings window
If your network does not display on the Confirm Wireless Settings window, connect to the correct network.
1. Select No, I want to choose another network, and then click Continue.
  
  A list of available wireless networks displays.
2. Select your wireless network from the list or type your network SSID in the Wireless Network Name field, and then type your password in the Password field.
3. Click Continue.
After the network connection is configured, click Done, and then disconnect the USB cable from the printer and the computer.
In the Printers & Scanners or Print & Scan window, click the name of your printer, click the minus sign , and then delete the USB installed printer.
Click the plus sign , and then click Add Printer or Scanner.
Click the name of your printer with the text Bonjour listed under Kind, click the Use or Print Using box, and then select the name of your printer in the pop-up menu.
Click Add to add the printer to the list.
Try to print.