HP Kundensupport - Wissensdatenbank

hp-contact-secondary-navigation-portlet

Aktionen
Ladevorgang läuft...

hp-share-print-widget-portlet

Aktionen
Ladevorgang läuft...

hp-concentra-wrapper-portlet

Aktionen
Ladevorgang läuft...

HP Z400 Workstation - Removing and Replacing the Hard drive

This document pertains only to HP Z400 Workstations with the following case design:

Before you begin

  • Turn off the workstation, and then disconnect all cables. Disconnect the Ethernet or modem cable before disconnecting the power cord.
  • Move the workstation to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the workstation.
  • Do not remove a component from its protective packaging until you are ready to install it.
  Warnung:
The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the workstation.
  Vorsicht:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.

Video overview (in English)

To view a video demonstrating the procedure for removing the hard drive, right-click Hard drive removal video and select Open link in new window/tab.

Replacement part information

The following HP part numbers are known to be compatible with this system:
Hinweis:
Part numbers are subject to change.
Description
Part Number
Requires Return
1TB SATA hard drive - 7,200 RPM, 3.5 inches form factor, and NCQ (Native Command Queuing) technology
508027-001 (Original)
Yes
146 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM
405430-001 (Modified)
Yes
300 GB SATA SQ hard drive - 7,200 RPM, 3.5 inches form factor, 1.0 inch high
453139-001 (Modified)
Yes
160 GB SATA SQ hard drive - 10,000 RPM, 3.5 inches form factor, 1.0 inch high
508029-001 (Modified)
Yes
250 GB SATA SQ hard drive - 7,200 RPM, 3.5 inches form factor, 8 MB cache
508028-001 (Original)
Yes
HP 300 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor, 1.0 inch high
413647-001 (Modified)
Yes
320 GB SATA hard drive - 7,200 RPM, 3.5 inches form factor, and NCQ (Native Command Queuing) technology
508026-001 (Original)
Yes
450 GB hot-plug Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor
495608-001 (Modified)
Yes
HP 300 GB Serial Attached SCSI (SAS) hard drive - 15,000 RPM, 3.5 inches form factor, 1.0 inches high
460579-001 (Modified)
Yes
300 GB SATA SQ hard drive - 10,000 RPM, 3.5 inches form factor, 1.0 inch high
502599-001 (Modified)
Yes
* If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. For more information about returning parts to HP select one of the links below:
Hinweis:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Hard drive removal

Step 1
With all cables disconnected from the workstation, remove the access panel.
For more information about removing the access panel, refer to the HP support document Instructions on how to remove the access panel.
Step 2
Disconnect the power and data cables from the drive.
Step 3
Pull out on the green release latch and slide the drive out of the drive cage.
Step 4
If the replacement drive does not include guide screws, remove and reuse the screws from this drive or use the spare screws provided on the drive cage.

Hard drive replacement

Step 1
Align the guide screws on the drive with the guide slots in the drive bay.
Step 2
Push the drive into the bay until it locks into place.
Step 3
Connect the power and data cables to the drive.
Step 4
Replace the access panel.


Land/Region: Flag Schweiz

hp-detect-load-my-device-portlet

Aktionen
Ladevorgang läuft...