hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Audio or sound issues? Try our automated HP Audio check!

    Information

    Fix and resolve Windows 10 update issue on HP Computer or Printer. Click here

    Information
    Create an HP account today!

     Connect with HP support faster, manage all of your devices in one place, view warranty information and more. Learn more​

hp-concentra-wrapper-portlet

Actions
Loading...

HP LaserJet Enterprise 700 M712 - Removal and replacement: Hard disk drive (HDD)

This document provides the procedures to remove and replace the hard disk drive.

Important:

When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.

Mean time to repair:10 minutes

Service level:Basic

Before performing service

Turn the printer power off

  • Disconnect the power cable.

    Warning:

    To avoid damage to the printer, turn the printer off, wait 30 seconds, and then remove the power cord before attempting to service the printer.

Use the table below to identify the correct part number for your printer. To order the part, go to www.hp.com/buy/parts.

Part information

HDD part number

CF235-67901

320 GB HP high-performance secure hard disk

CF235-67920

320 GB HP high-performance secure hard disk (government option)

Required tools

  • No special tools are required to install this kit.

After performing service

Turn the printer power on

  • Connect the power cable.

  • Use the power switch to turn the power on.

Post service test

Make sure that the printer initializes to a Ready state.

Print a configuration page to make sure that the printer is functioning correctly.

Remove the formatter PCA

Follow these steps to remove the formatter PCA.

  1. Locate the formatter and turn two thumb-screws (callout 1) counterclockwise to detach the formatter base plate from the chassis.

    Remove the formatter (1 of 2)

    Remove the formatter
  2. Pull the formatter away from the product to remove it.

    Tip:

    Reverse the removal steps to install the assembly.

    Remove the formatter (2 of 2)

    Remove the formatter

Remove the hard drive

Follow these steps to remove the hard drive.

  1. On the formatter, bend the plastic tab (callout 1) on the hard disk assembly toward the disk to disengage a tab underneath the formatter PCA.

    Remove the hard drive (1 of 2)

    Remove the hard drive
  2. Slide the hard disk (callout 1) in the direction indicated to remove it from the formatter PCA.

    Note:

    Set this part aside. It will be installed on the replacement formatter.

    Tip:

    Reverse the removal steps to install the assembly.

    Remove the hard drive (2 of 2)

    Remove the hard drive

Unpack the replacement assembly

Follow these steps to unpack the replacement assembly.

  1. Dispose of the defective part.

    Note:

    HP recommends responsible disposal of the defective part.

    http://www8.hp.com/us/en/hp-information/environment/product-recycling.html

  2. Unpack the replacement part from the packaging.

    CAUTION:

    Some parts are sensitive to electrostatic discharge (ESD). Always perform service work at an ESD-protected workstation or mat. If an ESD workstation or mat is not available, touch the sheet-metal chassis to provide a static ground before touching an ESD-sensitive assembly. Protect the ESD-sensitive assemblies by placing them in ESD pouches when they are out of the printer.

    Important:

    Make sure that all of the shipping materials (for example shipping tape) are removed from the replacement part prior to installation.

    Note:

    If the replacement part is a roller or pad, avoid touching the spongy part of it. Skin oils on the roller or pad can cause paper pickup and/or print-quality problems. HP recommends using disposable gloves when handling rollers or pads or washing your hands before touching rollers or pads.

  3. To install an assembly, reverse the removal steps.

    Note:

    When applicable, special installation instructions are provided for an assembly at the end of the removal procedure. Always completely read the removal instructions and follow all special installation instructions.


hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Canada

hp-detect-load-my-device-portlet

Actions
Loading...