hp-support-head-portlet

Actions
Loading...
HP Customer Support - Knowledge Base

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Information

    Fix intermittent print spooler service errors that may cause print jobs to fail post a Windows update. Click here

    Information
    Fix Windows 10 Update Issues

    Resolve Windows 10 or update issues on an HP computer or printer – Click here

hp-concentra-wrapper-portlet

Actions
Loading...

HP Z800 Workstation - Removing and Replacing the Front bezel

This document pertains only to HP Z800 Workstations with the following case design:

Before you begin

  • You need a Torx-15 screwdriver.
  • Turn off the workstation, and then disconnect all cables. Disconnect the Ethernet or modem cable before disconnecting the power cord.
  • Move the workstation to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the workstation.
  • Do not remove a component from its protective packaging until you are ready to install it.
  warning:
The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the workstation.
  caution:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.

Video overview (in English)

To view a video demonstrating the procedure for removing the front bezel, right-click Front bezel removal video and select Open link in new window/tab.

Replacement part information

The following HP part numbers are known to be compatible with this system:
note:
Part numbers are subject to change.
Description
Part Number
Requires Return *
Front bezel
534883-001 (Original)
No
* If a part is listed as "Yes" under "Requires Return" then the defective part needs to be returned to HP. For more information about returning parts to HP select one of the links below:
note:
For customers in countries/regions with RoHS legislation* (e.g. EU, China, etc.) restricting the use of hazardous substances in electrical equipment. The use of the Original Spare part is regulated by RoHS legislation. If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as the replacement part. If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the replacement part. In this case either the Original Spare or the Modified Spare may be shipped which will not affect performance or functionality of the unit.

Front bezel removal

Step 1
With all cables disconnected from the computer, remove the access panel.
For more information about removing the access panel, refer to the HP support document Instructions on how to remove the access panel.
Step 2
Remove the two Torx-15 screws that secure the right side panel to the bottom of the chassis.
Step 3
Slide the right side panel back about half an inch (1.3 cm) and then lift and remove the panel.
Step 4
Remove the two Torx-15 screws that secure the front bezel to the right side of the chassis.
Step 5
Place the computer in a standing position and remove the two Torx-15 screws that secure the front bezel to the left side of the chassis.
Step 6
Pull out on the top and bottom edges to disengage the bezel from the chassis and remove.

Front bezel replacement

Step 1
Position the front bezel over the chassis so that the top of the bezel is aligned with the handle and the front I/O openings are aligned with the connectors.
note:
Make sure the curved extensions near the top of the front bezel are correctly engaged with the top bezel and slots on both sides of the chassis.
Step 2
Press the top of the bezel into place until the screw holes on the bezel align with the mounting holes in the chassis.
Step 3
Replace the two Torx-15 screws that secure the front bezel to the top of the chassis.
Step 4
Press the bottom of the bezel into place until the screw holes on the bezel align with the mounting holes in the chassis.
Step 5
Replace the two Torx-15 screws that secure the front bezel to the bottom of the chassis.
Step 6
Position the right side panel over the chassis so that the aligning pins engage with the keyholes in the chassis rail.
Step 7
Press down on the right side panel and slide it forward until it locks in place.
Step 8
Replace the two Torx-15 screws that secure the right side panel to the bottom of the chassis.
Step 9
Replace the access panel.

hp-feedback-input-portlet

Actions
Loading...

hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
Country/Region: Flag Canada

hp-detect-load-my-device-portlet

Actions
Loading...