hp-support-head-portlet

Acciones
Cargando...
Soporte al cliente de HP: base de conocimientos

hp-contact-secondary-navigation-portlet

Acciones
Cargando...

hp-share-print-widget-portlet

Acciones
Cargando...
  • Información

    Solucione errores intermitentes en la cola de impresión/con el spooler de impresión que podrían causar fallos en los trabajos de impresión tras una actualización de Windows. Haga clic aquí

    Información
    Corrija errores en Win 10

    Resuelva problemas de actualización  de Windows 10  en un PC o impresora HP – haga clic aquí

hp-concentra-wrapper-portlet

Acciones
Cargando...

Removing and Replacing the Top Cover for HP ENVY 15-u000 x360 Convertible PCs

This document applies to HP ENVY 15-u000 x360 convertible computers.
 HP ENVY 15-u000 x360 convertible computer

Before you begin

  • Have a Phillips head screwdriver, tweezers or needle-nose pliers, and a nonmetallic stick or similar prying tool.
  • Turn off the computer. Disconnect the Ethernet or modem cable. Disconnect the power cord.
  • Transfer the computer to a clear, flat, stable work surface over a non-carpeted floor.
  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.
  • Do not remove a component from its protective packaging until you are ready to install it.
  advertencia:
Before starting, power off the computer and wait for components to cool before starting these procedures.
  atención:
This product contains components that can be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected to a grounded surface.
  atención:
Procedures in this document are provided by HP for qualified service agents and as a courtesy to its customers. Servicing internal components increases the risk of damaging the computer which might not be covered under warranty. Understand the risk and refer to the product's warranty before attempting to service the computer.

Video overview

View the following video before using the steps in this article.
nota:
The video and graphics in this article depict a specific configuration of notebook computer. These same removal and replacement procedures apply to all configurations for all HP ENVY 15-u000 x360 Convertible notebook computers.

Removing the top cover

Follow the steps in this section to remove the top cover.
  advertencia:
Make sure the computer is disconnected from power before starting.
Step 1
Find the two rubber feet and the two Mylar screw covers on the base enclosure.
The two rubber feet and Mylar screw covers
Step 2
Remove the two rear rubber feet...
Removing the rubber feet
...and two Mylar screw covers from the base enclosure.
Removing the Mylar screw covers
Step 3
Remove the fourteen Phillips-head screws that secure the top cover to the base enclosure.
Fourteen screw locations that secure the top cover to the base enclosure
Step 4
Turn the computer over and open the display panel.
Opening the display cover
Step 5
Carefully separate the edges of the top cover from the base enclosure.
Prying the edges of the top cover to separate it from the base enclosure
Step 6
Lift the front edge of the top cover until you have access to the battery connector on the system board.
Lifting the front edge of the top cover
Step 7
Disconnect the battery cable from its connector on the system board.
Disconnecting the battery cable from the system board
Step 8
Using minimal force, carefully lift the locking bar up on the touchpad board connector...
Lifting the locking bar on the touchpad ribbon cable connector
..and disconnect the touchpad board ribbon cable from the system board.
Disconnecting the touchpad ribbon cable from the system board
Step 9
Using minimal force, carefully lift the locking bar up on the keyboard connector and disconnect the keyboard ribbon cable from the system board.
Disconnecting the keyboard cable
Step 10
Using minimal force, carefully lift the locking bar up on the keyboard light connector and disconnect the keyboard light ribbon cable from the system board.
With all the cables disconnected, remove the top cover.
Disconnecting the keyboard light connector cable

Replacing the top cover

Use the steps in this section to replace the top cover.
Step 1
If installing a new top cover, remove the touchpad board and install it on the new top cover.
For instructions to remove and replace the touchpad board, see the HP support document, Removing and Replacing the Touchpad Board for HP ENVY 15-u000 Convertible Notebook PCs.
Touchpad board
Step 2
Place the top cover into position on the base enclosure so that you have access to the battery, keyboard, touchpad, and keyboard light connectors on the system board.
Placing the cover in position on the base enclosure
Step 3
Carefully insert the power button board ribbon cable into the power button board connector on the system board and press the locking bar down to lock the cable into place.
Reconnecting the power button board ribbon cable
Step 4
Carefully insert the keyboard ribbon cable into its connector on the system board and gently push down on the locking bar to secure it.
Reconnecting the keyboard ribbon cable
Step 5
Carefully insert the touchpad button board ribbon cable into the touchpad button board connector on the system board and press the locking bar down to lock the cable into place.
Reconnecting the touchpad button board ribbon cable
Step 6
Connect the battery cable into its connector on the system board.
The battery cable reconnected
Step 7
Lower the top cover into place on the base enclosure.
Lowering the top cover into place on the base enclosure
Step 8
Apply pressure to the edges of the top cover to snap it into place.
Pressing the edges of the top cover to snap it into place
Step 9
Close the display panel and turn the computer over.
Closing the display panel and turning over the computer
Step 10
Replace the fourteen screws that secure the top cover to the base enclosure.
Fourteen screw locations
Step 11
Replace the two Mylar screw covers...
Replacing the Mylar screw covers
... and two rear rubber feet onto the base enclosure.
Replacing the rubber feet on the base enclosure

hp-feedback-input-portlet

Acciones
Cargando...

hp-feedback-banner-portlet

Acciones
Cargando...

hp-country-locator-portlet

Acciones
Cargando...
País/región: Flag Bolivia

hp-detect-load-my-device-portlet

Acciones
Cargando...