HP Support

hp-contact-secondary-navigation

Actions
Loading...

hp-share-print-widget

Actions
Loading...

hp-concentra-wrapper

Actions
Loading...

Setting up the All-in-One (Hardware)

Introduction
This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.
This document includes the following steps to set up the product:
  • Unpack the All-in-One
  • Connect the power cord and adapter
  • Turn on power
  • Select the language/region
  • Load plain paper
  • Install the cartridges
  • Align the printer
Setting up a new All-in-One
Follow these steps to set up the product hardware and install the software.
Step one: Unpack the All-in-One
  1. Remove all the tape from the front and back of the product.
    Figure : Remove the packing tape
    Graphic: Remove the packing tape
  2. Open the product and remove all the packaging materials from inside the product.
    Figure : Remove the packing material from inside the product
    Graphic: Remove the packing material from inside the product
  3. Place the HP eStation Zeen (control panel display) into its docking port.
    Figure : Place the HP eStation Zeen into its docking port
    Graphic: Place the HP eStation Zeen into its docking port
Step two: Connect the power cord and adapter
  1. Connect the power cord to the back of the product.
    Figure : Connect the power cord to the back of the product
    Graphic: Connect the power cord to the back of the product
  2. Connect the power cord to the power supply.
    Figure : Connect the power cord to the power supply
    Graphic: Connect the power cord to the power supply
  3. Connect the power cord to the electrical outlet.
    Figure : Connect the power cord to the electrical outlet
    Graphic: Connect the power cord to the electrical outlet
Step three: Turn on power
Press the Power button () to turn on the product.
Figure : Press the Power button
Graphic: Press the Power button
Step four: Follow the Setup Wizard
The Setup Wizard will display on the HP eStation Zeen. Follow the prompts in the Setup Wizard to finish setting up the product.
Figure : Follow the Setup Wizard
Graphic: Follow the Setup Wizard
  1. Raise the output tray into the open position, and then open the input tray door.
  2. Slide the paper width guide to its outermost position.
    Figure : Slide the paper width guide outward
    Illustration of sliding the paper width guide outward
  3. Insert the stack of paper into the input tray with the short edge forward and the print side down.
    Figure : Load paper into the input tray
    Illustration of loading paper into the input tray
  4. Adjust the paper width guide so that it rests against the stack of paper.
    Figure : Slide the paper width guide inward
    Illustration of sliding the paper width guide inward
  5. Lower the output tray, and then close the input tray door.
Step six: Install the cartridges
 note:
Do not reuse old cartridges. Old cartridges might damage the new printhead.
  1. Press the Power button () to turn on the product, if it is not already turned on.
  2. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing.
    Figure : Open the cartridge access door
    Illustration of opening the cartridge access door
  3. On the new cartridge, pull the orange pull-tab straight back to remove the plastic wrap.
    Figure : Remove the plastic wrap on the cartridge
    Graphic: Remove the plastic wrap
  4. Twist the orange cap counter clockwise to snap it off the cartridge.
    Figure : Remove the orange cap
    Graphic: Remove the orange cap
  5. With the cartridge contacts facing the printhead, slide the cartridge into the empty slot, and then press down on the cartridge until it clicks firmly into place.
     note:
    Make sure that the color-coded icon on the cartridge matches the color-coded icon on the carriage slot.
    Figure : Install the cartridge
    Illustration of installing the cartridge
  6. Repeat these steps to install the other cartridges.
  7. Close the cartridge access door. The carriage returns to the right side of the product.
    Figure : Close the cartridge access door
    Illustration of closing the cartridge access door
Step seven: Align the product
After loading plain white paper, touch OK on the product control panel. The product automatically prints an alignment page to align the cartridges.
Figure : Example alignment page
Graphic: Example alignment page
Getting started with ePrint
Now you can stay connected and productive on the go with ePrint. ePrint lets you print directly to your ePrint-enabled HP printer using a smartphone, notebook, or other mobile device. For additional information related to setting up and using ePrint, click the link provided.

hp-online-communities

Actions
Loading...
EmptyPortlet
Contact HP

Contact HP

Let HP help you find the answer or identify a service location. Contact us >

Country: United States