HP Support

hp-contact-secondary-navigation

Actions
Loading...

hp-share-print-widget

Actions
Loading...

hp-concentra-wrapper

Actions
Loading...

Setting up the All-in-One (Hardware)

Introduction
This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.
This document includes the following steps to set up the product:
  • Unpack the All-in-One
  • Check the contents of the box
  • Attach the control panel faceplate (if not attached)
  • Connect the supplied phone cord
  • Connect the power cord and adapter
  • Turn on power
  • Select the language/region
  • Set the date and time
  • Install the cartridges
  • Load plain paper
  • Load paper in the photo tray
  • Align the cartridges
Setting up the All-in-One
Follow these steps in order.
Step one: Unpack the All-in-One
  1. Remove all tape and protective film from the lid and from the front and back of the product
  2. Lift the control panel display and remove the protective film. You can adjust the angle of the display to a position suitable for viewing.
    Figure : Adjust the display
    Remove the film from the display screen
The contents might vary by country/region. See the packaging for a list of items shipped in the box.
Step three: Attach the control panel faceplate (if not attached)
  1. Position the control panel faceplate over the buttons on the product.
    Figure : Faceplate position
    Place the faceplate over the control panel buttons
  2. Press down firmly on all edges of the faceplate until it snaps into place. Make sure that all buttons come through the holes in the faceplate.
Step four: Connect the supplied phone cord
Connect one end of the supplied phone cord to the port labeled 1-LINE and the other to a wall jack.
Figure : Connect the phone cord
Connect the supplied phone cord
Step five: Connect the power cord and adapter
  1. Connect the power cord to the power adapter.
  2. Connect the power adapter to the power adapter connection on the back of the HP All-in-One.
  3. Connect the power cord to a wall outlet or surge protector.
Figure : Power connections
Connect the power cord and adapter
Step six: Turn on power
  1. Press the On button () to turn on the HP All-in-One.
  2. After you press the On button (), wait for the prompt on the control panel display before continuing.
Step seven: Select the language/region
Follow these steps if the display prompts you to set the language and country/region.
  1. Use the arrow keys to select your language from the list of up to 25 languages, press the OK button, and then confirm.
    Figure : Arrow keys
  2. Use the arrow keys to select your country/region, press the OK button, and then confirm.
Step eight: Set the date and time
  1. Press the Setup button ().
  2. Press the down arrow (to highlight Tools, and then press OK.
  3. Press the down arrow (to highlight Date and Time, and then press OK.
  4. Enter the month, day, and year by pressing the appropriate numbers on the keypad. Depending on your country/region setting, you might enter the date in a different order.
  5. Enter the hours and minutes.
  6. If your time is displayed in the 12-hour format, press 1 for AM, or 2 for PM. The new date and time settings appear on the display.
 note:
Use only the ink cartridges that came with the HP All-in-One. The ink in these cartridges is specially formulated to mix with the ink in the print head assembly at first-time setup.
Follow the steps below to install the ink cartridges.
  1. Open the access door by lifting from the front center of the HP All-in-One, until the door locks into place.
    Figure : Opening the access door
  2. Squeeze the bottom of each latch to release it, and then lift the latch.
      Figure : Lifting the latch
    1. Ink cartridge latch for the black ink cartridge
    2. Ink cartridge latches for the color ink cartridges
  3. Lift all the six latches.
  4. Match the color and pattern of the ink cartridge to the color and pattern above the latches.
  5. Push the black ink cartridge into the first slot on the left, and close the latch.
    Figure : Black ink cartridge installation
  6. Repeat with each of the color ink cartridges.
    Figure : Color ink cartridge installation
  7. Make sure each latch is secure.
    Figure : All ink cartridges installed
  8. Close the access door.
    Figure : Closing the access door
  1. Pull the main tray extender towards you to extend the main tray.
  2. Slide the paper-width and paper-length guides to their outermost positions.
    Figure : Extend main tray and guides
  3. Load the paper with the side to be printed facing down. Verify that the stack of paper fits loosely under the tab on the paper-length guide.
  4. Adjust the paper-width and paper-length guides inward until they stop at the edges of the paper.
    Figure : Adjust paper guides
  5. Push in the main tray.
    Figure : Main tray pushed in
  1. Lift the output tray and extend the photo tray.
    Figure : Extend the photo tray
  2. Load up to 20 sheets of paper into the photo tray with the glossy side facing down. Make sure that the stack of paper fits loosely under the tab on the paper-length guide.
    Figure : Load the photo paper with the glossy side facing down
     note:
    When using tabbed paper, insert the paper so that the tab is closest to you.
  3. Adjust the paper-width and paper-length guides inward until they stop at the edges of the paper.
  4. Push in the photo tray.
    Figure : Push in the photo tray
  5. Lower the output tray.
  1. Press the OK button to start the alignment process. Wait a few minutes for the the product to complete the alignment and print the alignment page.
     caution:
    Do not disconnect or turn off the HP All-in-One during this time. You might hear the HP All-in-One making noises.
  2. After the alignment page is printed, check the display for status, and then press the OK button. Recycle or discard the alignment page.

hp-online-communities

Actions
Loading...
EmptyPortlet
Contact HP

Contact HP

Let HP help you find the answer or identify a service location. Contact us >

Country: United States