hp-support-head-portlet

Actions
Loading...

HP Customer Support

hp-contact-secondary-navigation-portlet

Actions
Loading...

hp-share-print-widget-portlet

Actions
Loading...
  • Alert
    Need help after upgrading to Windows 10?

    Here are solutions to common problems seen after upgrading.

    View article

hp-concentra-wrapper-portlet

Actions
Loading...

HP PSC 1500 All-in-One Printer Series- Setting up the All-in-One (Hardware)

Introduction
This document explains how to set up the physical parts of the product. Complete these steps before you install the product software on your computer.
This document includes the following steps to set up the product:
  • Unpack the All-in-One
  • Check the contents of the box
  • Attach the control panel overlay, if not attached
  • Connect the power cord and adapter
  • Turn the product on
  • Load plain white paper
  • Insert the cartridges
  • Align the cartridges
Setup the hardware
Follow these steps in order.
Step one: Unpack the All-in-One
Remove all tape and packing material from the product.
Figure : Remove all packing materials
The contents might vary by country/region. See the packaging for a list of items shipped in the box.
Step three: Attach the control panel overlay, if not attached
  1. Hold the control panel overlay with the printed side facing you and gently bend the bottom tab of the control panel overlay away from you.
    Figure : Bend bottom tab
  2. Remove the bottom tab and the backing from the overlay.
    Figure : Remove bottom tab
  3. Lift the lid of the product. Insert the tabs of the overlay into the device. Make sure the tabs are inserted correctly before sticking the overlay to the device.
    Figure : Open lid and insert the overlay tabs into place
  4. Press down on the overlay to make sure it is firmly attached. Do not press on the LCD area. The tabs must be in the slots.
    Figure : Press down on the overlay to attach it
Step four: Connect the power cord and adapter
  1. Plug the printer end of the power adapter into the back of the printer.
  2. Plug the adapter end of the power cord into the power adapter.
  3. Plug the remaining end of the power cord into a grounded wall outlet or surge protector.
    Figure : Connect the power cord and adapter
  1. Printer end of the adapter
  2. Adapter end of the power cord
  3. Plug end of the power cord
Step five: Turn the product on
Press the Power button to turn the product on.
Figure : Turn the product on
After you press the button, the green light flashes, and then becomes solid. This might take up to a minute.
  1. Open the paper tray door.
    Figure : Open the paper tray door
  2. Pull the paper tray extender toward you, as far as it will go. Flip the paper catch at the end of the paper tray extender to open the extender the rest of the way.
     note:
    Legal paper might get caught on the paper tray extender if it is fully extended when you print onto legal paper. To avoid a paper jam when using legal-size paper, do not open the paper tray extender.
  3. Squeeze and hold the tab on the top of the paper-width guide, then slide the paper-width guide to its outermost position.
    Figure : Slide the paper-width guide to the outermost position
  4. Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
    • Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
    • Make sure all the paper in the stack is the same size and type.
  5. Insert the stack of paper into the paper tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
     note:
    If using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the paper tray.
    Figure : Insert paper into the All-in-One
    Squeeze and hold the tab on the top of the paper-width guide, then slide the paper-width guide inward until it stops at the edge of the paper.
    Figure : Slide the paper-width guide to the edge of the paper
    Do not overload the paper tray; make sure the stack of paper fits within the paper tray and is no higher than the top of the paper-width guide.
  1. Lower the access door until it stops. Make sure the carriage moves to the right side.
    Figure : Lower the access door
    Figure : Carriage for the cartridges
  2. Pull the pink tab to remove the protective tape from both cartridges.
    Figure : Remove the tape
     caution:
    Do not touch the copper-colored contacts or retape the cartridges.
  3. Insert the tri-color cartridge in the left slot of the carriage, and then push the cartridge firmly into the slot until it snaps into place.
    Figure : Push the cartridge into place
  4. In the same way, insert the black cartridge in the right slot of the carriage.
      Figure : The cartridges in the proper position
    1. Tri-color print cartridge
    2. Black print cartridge
  5. Close the access door.
Step eight: Align the cartridges
After you insert the cartridges, a cartridge alignment page prints. This might take a few minutes.
  1. Lift the lid of the product.
  2. Place the top of alignment page face down in the right front corner of the glass.
    Figure : Place the alignment page face down
  3. Close the lid.
  4. Press the Start Scan button.
    Figure : Start Scan button
    The Power button light blinks during the alignment process. After the light stops blinking, alignment is complete.

hp-feedback-input-portlet

Actions
Loading...

hp-online-communities-portlet

Actions
Loading...

Ask the community!


Support Forum

Support Forum

Join the conversation! Find Solutions, ask questions, and share advice with other HP product owners. Visit now


hp-feedback-banner-portlet

Actions
Loading...

hp-country-locator-portlet

Actions
Loading...
United States

hp-detect-load-my-device-portlet

Actions
Loading...